Şuradaki yenilikler:

SOLIDWORKS Kullanıcı Forumu

SOLIDWORKS kullanıcılarının 3DEXPERIENCE Works: SOLIDWORKS masaüstü, bulut bağlantısı ve saf bulut hakkında keşif, etkileşim ve paylaşım yaptığı yer.

SOLIDWORKS ID'nizle veya yeni ya da mevcut bir 3DEXPERIENCE ID'siyle oturum açmanız yeterli.

Sıralama ölçütü::
SolidworksAssemblies
SOLIDWORKS User Forum
1 yıl önce
Say I have a subassembly that has a shaft in it. The shaft is constrained via mates in all degrees of freedom except for rotation. I then take that subassembly and drop it into a higher-level assembly. How do I rotate the shaft from the higher-level assembly?
SOLIDWORKS User Forum
1 yıl önce
SOLIDWORKS User Forum
1 yıl önce
SOLIDWORKS User Forum
1 yıl önce
SOLIDWORKS User Forum
1 yıl önce
SOLIDWORKS User Forum
1 yıl önce
SOLIDWORKS User Forum
1 yıl önce
Hey everyone! Is there a way in Solidworks 2017 to explode a multi-body part in an exploded view of an assembly? I cannot use the "reuse subassembly explode" button since it is a part, not an assembly. And also I found a solution but it only works in solidworks 2020 where there is a "from part" button under options but it is not present in solidworks 2017. SolidworksAssemblies
SOLIDWORKS User Forum
1 yıl önce
Why are blocks excluded in pack and go? Is it hidden somewhere in custom decals or the drawings check box? My parts are still looking at the block file in the previous folder. I really hate that solidworks is using full file locations as reference.
SOLIDWORKS User Forum
1 yıl önce
Using SolidWorks 2016 on a Dell Precision 7520 with 24G RAM. I find this when creating a pattern in an assembly: I start typing the dimensions for the pattern and Solidworks tries to update everything with each keystroke. This makes creating a pattern very slow. Is there a way to turn off this feature so Solidworks won't try to do anything until I hit enter? SolidworksAssemblies
SOLIDWORKS User Forum
1 yıl önce
Hi, I am trying to modify a part using a design table in assembly. Can this be done using global variables? I was told that design tables cannot drive part dimensions in assembly. Thanks! SolidworksAssemblies
SOLIDWORKS User Forum
1 yıl önce
İs it possible to repair it. SolidworksAssemblies
SOLIDWORKS User Forum
1 yıl önce
Hi, I am trying to extract bodies & parts from an assembly to create a new separate assembly. Attached is a photo of what I mean. I want all the highlighted items to be extracted into a new assembly that can be modified. Not too sure how to do this.
SOLIDWORKS User Forum
2 yıl önce
Hi, Am using SOLIDWORKS-2017. When i try to Pack and Go an assembly , the folder structure is not working. By default its opting for "Flatten to single folder". Am unable to change it.
SOLIDWORKS User Forum
2 yıl önce
is there a way to insert smart fastener in between the sheets? (in this case i want to insert a nut and a washer in between the plates). SolidworksAssemblies
SOLIDWORKS User Forum
2 yıl önce
Hello, I have a Solidworks part file like below. I want to generate separate 3 parts highlighted in different colors. How can I generate 3 separate part ? Thank in advance SolidworksAssemblies
SOLIDWORKS User Forum
2 yıl önce
I changed spur gear's components like diameter, module, etc. but they are not updated on the screen. I attached the file. SolidworksAssemblies
SOLIDWORKS User Forum
2 yıl önce
Hi, in the past I was told to use Counterbore to embed the head of the screws under the Hole Wizard. However, when I chose Counterbore, the minimum size is M5. How come? I want to embed the head of screws like the following in the frames.
SOLIDWORKS User Forum
2 yıl önce
Hi to everyone.I have two parallel panels (vertical) and i 'd like to add a third panel (horizontal) with a coincident mate on two panels . In one panel its OK but when i try to make coincident mate to other panel i have an error . How can i add the second mate? (if its possible) Look scr(13) Thank you for your time Kostas SolidworksAssemblies
SOLIDWORKS User Forum
2 yıl önce
Could anyone please help me look at the assembly I attached? I was unable to rotate the leaves of the hinge subassembly within the main assembly. I have already made my subassembly flexible. SolidworksAssemblies
SOLIDWORKS User Forum
2 yıl önce
Hi, I want to duplicate part of an assembly but the parts of the duplicated one should be able to move independently from the originals. Also, if I modify the components of the original part, the corresponding components of the duplicated one should automatically be modified. Could you please let me know what is the best way to do this? SolidworksAssemblies
SOLIDWORKS User Forum
2 yıl önce
Hello, the question sounds terrible but I will try and describe it better. So I need an Assembly Custom Property to add part custom properties. For example I have 3 different parts in an assembly that have a custom property called number. The numbers are 1,2,3 I was hoping the assembly would add these and give me 6.
SOLIDWORKS User Forum
2 yıl önce
Hello, does anyone know if you can supress a folder in specific configurations at the same time, or does anyone have a macro for it? thx! SolidworksAssemblies
SOLIDWORKS User Forum
2 yıl önce