Explore the Miter Flange feature, including sketching the profile, edge selection, and other pertinent options. Create a miter flange. Learn and understand the different options for miter flange.
Create a spring using a sweep feature defined in the context of an assembly. Then, animate the spring by adding a linear motor in MotionManager. Create an animation. Model a spring using an in-context sweep. Add a linear motor to stretch and compress the spring. Understand the impact of rebuild errors on animations.
Add each of the six mechanical mate types to control the degrees of freedom of components when designing mechanisms. Mate a cylinder, plane, or point to a series of tangent faces with a cam follower mate. Limit the rotational movement between two components with a hinge mate. Move one component linearly to move another component rotationally with a rack and pinion mate. Add a pitch relation between the rotation of one component and the translation of another with a screw mate. Rotate two components relative to one another with a gear mate or a universal joint mate.
Constrain a point or a vertex of a component to a path in an assembly. Then, control the pitch, yaw, and roll of the component as it moves along the path. Specify the entities for a path mate. Edit a path mate to control pitch, yaw, and roll of the component.
Create a note with text that is linked to existing dimensions and custom properties. Link a note to a dimension. Edit the title block of a drawing to add notes linked to a model's properties. Add drawing property information to populate a title block.
Center a component relative to two faces of a groove using a width mate. Add a width mate to center a component relative to two faces of another component. Understand the degrees of freedom that are constrained by a width mate.
Create basic, aligned, offset, and partial or half-section views, including scope and advanced properties. Add several types of section views to a drawing. Define section view properties. Modify section views.
Insert annotations into existing drawing views, including custom notes, geometric tolerances, and blocks. Create annotations and symbols. Create blocks from geometry and notes. Save a block to a file. Insert a block into a drawing.
The Belt/Chain assembly feature links idlers, pulleys, or sprockets together to achieve the intended rotation of several components simultaneously. Optionally, you can create a belt or chain component part. Select edges of pulleys and idlers for a belt/chain assembly feature. Set the properties of a belt/chain assembly feature.
Use drawing view commands that are specific to working with assembly models including broken out section views, alternate position views, and exploded views. Use drawing view properties to represent assembly configurations. Create a broken-out section view to show internal components of the assembly. Create an alternate position view using an existing or a new configuration. Create an exploded assembly drawing view.
Mirror Component creates opposite-hand, but otherwise identical, versions of parts or subassembies. Specify which components are mirrored and which are purely copied (i.e. fasteners, which should not be mirrored). The geometry of a mirrored component changes to create a truly mirrored version, known as an \"opposite-hand\" version. Mirror components about an assembly plane. Create mirrored versions of parts in an assembly. Create opposite-hand versions of parts.
Blocks group sketch entities and dimensions together so that they move as one in a sketch. Together with a layout sketch, you can go directly from an assembly sketch to the full assembly. Create, edit and save blocks. Create a layout sketch of an assembly using blocks. Build assembly components based on the existing blocks.
Create display states to control the visibility and display style of components. Display states can be linked to configurations of an assembly. Display states can control hide/show state, display mode, appearance, and transparency of components. Add display states to an assembly. Modify visual properties of components with display states. Explore component selection techniques. Use the display pane. Open an assembly to a specific configuration and display state. Link display states to configurations.
The linear coupler mate links the translation of one component to the translation of another component. The translation occurs along an axis you define relative to the assembly origin or a reference component. Select the faces and reference components to define a linear coupler mate. Set the ratio of motion of one component relative to another.
Constrain two similar entities (points, edges, faces, etc) to be symmetric about a plane or planar face. A symmetry mate does not force the components to be symmetric, just the entities you select. Understand the acceptable selections for a symmetry mate. Constrain two planar faces to be symmetric about a reference plane.
Adjust the mesh density to adjust accuracy of a simulation. Run a simulation. Use the SimulationXpress wizard to view results such as the stress, displacement, deformation, and factor of safety of the simulation. Generate and save an eDrawings file or word document both of which display the results of the simulation. Adjust a mesh in a simulation. Run a simulation. Interpret the results of a simulation. Generate an eDrawing file or Microsoft Word document with the results.
Use surfacing techniques to create custom blends where fillets produce undesireable results. Remove unwanted faces from a model using the Delete Face command. Use Face Curves and sketches to create a trimming boundaries. Trim faces to form a clean boundary for the blend. Use the Filled Surface command to create a surface tangent to all adjacent faces. Use Knit Surface to combine the surface bodies in the model. Use Thicken to transform the surfaces into solid geometry.
Create a variable radius fillet where you set the radius value at selected vertices and control points. Also, you can set the radius to zero to force the fillet to converge to a point. Create a fillet where the radius varies along the selected edge. Modify the radius value at vertices or control points. Create zero radius fillets where the fillet must converge to a point.
Loft creates a feature by making transitions between profiles. A loft can be a base, boss, cut, or surface. By specifying constraints and connection parameters, the desired result can be achieved. Create basic loft feature between two profiles. Refine the shape with a centerline curve, end constraints, and connection points. Select loft profiles and connection points correctly.
Learn the best practices for creating sweep profile sketches. Add relationships between the profile sketch entities and the guide curves. Create sketch relations that ensure the correct shape of the profile along the entire path. Set up the path and guide curves before creating the profile sketch. Add pierce relations between the guide curves and the profile sketch. Create a sweep feature with guide curves. Use perpendicular and parallel relations to define the sweep profile.
Connect existing components using orthogonal tubes and standard fittings from the library. Use the Auto Route feature to automatically generate routes Add standard fittings to assemblies. Create orthogonal routes between features.
Analyze different regions of a part to identify which portions of the part are at the target thickness, and assess which regions may lead to issues when creating a mold. Learn to use Thickness Analysis to display regions of a part are that are not at the target thickness. Save and view a Thickness Analysis report.
Use the various Mold Tools to prepare a part for injection molding, including scaling, split line, parting surface, and shut-off surfaces. After preparing the part, you create the core and cavity. Identifty the parting plane. Create a parting surface. Create shut-off surfaces. Create mold body, core and cavity.
Insert a reducing outlet tee into an existing route and orient it using keyboard shortcuts and a triad. Use the Auto Route tool to connect the pipes resulting from the additional feature. Add in-line fittings to existing routes. Use keyboard shortcuts and the triad to orient and position an in-line fitting.
