Copy and derive a sketch to use the original sketch more than once. A copied sketch is not related to the original, whereas a derived sketch changes if the original sketch every changes. Create a derived sketch that retains the same shape as the original sketch. Copy a sketch. Modify the position and dimensions of a sketch. Create a loft through three profile sketches.
Lesson
2 years ago
ENG
JPN
Create fillet beads and weld beads in a part. Learn the advantages of and differences between both features. Understand when to use each kind of weld. Create fillet beads and weld beads. Understand the advantages and disadvantages of each feature as well as when to use them. Use intermittent and staggered welds.
Lesson
1 year ago
ENG
JPN
Verify that a model is symmetric. This is helpful for splitting a part into the smallest symmetrical body for simulation analysis. Evaluate a model for symmetry. Understand the options and results within the Symmetry Check tool. Split a part into the smallest symmetrical body for use in simulation analysis.
Lesson
2 years ago
ENG
JPN
Explore the Miter Flange feature, including sketching the profile, edge selection, and other pertinent options. Create a miter flange. Learn and understand the different options for miter flange.
Lesson
1 year ago
ENG
JPN
Contour selection options allow individual contours to be selected within a sketch. By making use of contour selection techniques, a single sketch can be used to produce multiple features. Use the Contour Select Tool to pre-select contours for a feature. Use the Selected Contours options for a feature to define areas of a sketch to use. Use a single sketch to generate multiple features. Understand the icons displayed when using selected contours and sharing sketches.
Lesson
5 months ago
ENG
FRA
DEU
JPN
CHS
Mirror existing sketch entities with the Mirror Entities tool or by adding symmetric relations. Or, dynamically mirror sketch entities as you create them. Mirror sketch entities that you previously created. Dynamically mirror sketch entities as you create them. Add symmetric relations to sketch entities to mirror the entities.
Lesson
5 months ago
ENG
FRA
DEU
JPN
CHS
Add each of the six mechanical mate types to control the degrees of freedom of components when designing mechanisms. Mate a cylinder, plane, or point to a series of tangent faces with a cam follower mate. Limit the rotational movement between two components with a hinge mate. Move one component linearly to move another component rotationally with a rack and pinion mate. Add a pitch relation between the rotation of one component and the translation of another with a screw mate. Rotate two components relative to one another with a gear mate or a universal joint mate.
Lesson
1 year ago
ENG
JPN
Create basic, aligned, offset, and partial or half-section views, including scope and advanced properties. Add several types of section views to a drawing. Define section view properties. Modify section views.
Lesson
1 year ago
ENG
JPN
Insert annotations into existing drawing views, including custom notes, geometric tolerances, and blocks. Create annotations and symbols. Create blocks from geometry and notes. Save a block to a file. Insert a block into a drawing.
Lesson
1 year ago
ENG
JPN
Use drawing view commands that are specific to working with assembly models including broken out section views, alternate position views, and exploded views. Use drawing view properties to represent assembly configurations. Create a broken-out section view to show internal components of the assembly. Create an alternate position view using an existing or a new configuration. Create an exploded assembly drawing view.
Lesson
2 years ago
ENG
JPN
Mirror Component creates opposite-hand, but otherwise identical, versions of parts or subassembies. Specify which components are mirrored and which are purely copied (i.e. fasteners, which should not be mirrored). The geometry of a mirrored component changes to create a truly mirrored version, known as an \"opposite-hand\" version. Mirror components about an assembly plane. Create mirrored versions of parts in an assembly. Create opposite-hand versions of parts.
Lesson
1 year ago
ENG
JPN
Blocks group sketch entities and dimensions together so that they move as one in a sketch. Together with a layout sketch, you can go directly from an assembly sketch to the full assembly. Create, edit and save blocks. Create a layout sketch of an assembly using blocks. Build assembly components based on the existing blocks.
Lesson
2 years ago
ENG
JPN
Create display states to control the visibility and display style of components. Display states can be linked to configurations of an assembly. Display states can control hide/show state, display mode, appearance, and transparency of components. Add display states to an assembly. Modify visual properties of components with display states. Explore component selection techniques. Use the display pane. Open an assembly to a specific configuration and display state. Link display states to configurations.
Lesson
2 years ago
ENG
JPN
Use surfacing techniques to create custom blends where fillets produce undesireable results. Remove unwanted faces from a model using the Delete Face command. Use Face Curves and sketches to create a trimming boundaries. Trim faces to form a clean boundary for the blend. Use the Filled Surface command to create a surface tangent to all adjacent faces. Use Knit Surface to combine the surface bodies in the model. Use Thicken to transform the surfaces into solid geometry.
Lesson
3 months ago
ENG
JPN
Use the sketch tools Convert Entities and Offset Entities to reference sketch entities and model geometry to create new sketch entities. If the original geometry changes, then the converted and offset entities also change. Create converted entities into a new sketch. Create offset entities. Create a slot using offset entities.
Lesson
5 months ago
ENG
FRA
DEU
JPN
CHS
Create a variable radius fillet where you set the radius value at selected vertices and control points. Also, you can set the radius to zero to force the fillet to converge to a point. Create a fillet where the radius varies along the selected edge. Modify the radius value at vertices or control points. Create zero radius fillets where the fillet must converge to a point.
Lesson
2 years ago
ENG
JPN
Create fillets and chamfers to modify geometry in a sketch. Set the size and options for the sketch fillets and sketch chamfers. Create fillets and chamfers in a sketch. Understand the options for creating sketch fillets and sketch chamfers.
Lesson
5 months ago
ENG
FRA
DEU
JPN
CHS
Loft creates a feature by making transitions between profiles. A loft can be a base, boss, cut, or surface. By specifying constraints and connection parameters, the desired result can be achieved. Create basic loft feature between two profiles. Refine the shape with a centerline curve, end constraints, and connection points. Select loft profiles and connection points correctly.
Lesson
2 years ago
ENG
JPN
Learn the best practices for creating sweep profile sketches. Add relationships between the profile sketch entities and the guide curves. Create sketch relations that ensure the correct shape of the profile along the entire path. Set up the path and guide curves before creating the profile sketch. Add pierce relations between the guide curves and the profile sketch. Create a sweep feature with guide curves. Use perpendicular and parallel relations to define the sweep profile.
Lesson
2 years ago
ENG
JPN
Use the various Mold Tools to prepare a part for injection molding, including scaling, split line, parting surface, and shut-off surfaces. After preparing the part, you create the core and cavity. Identifty the parting plane. Create a parting surface. Create shut-off surfaces. Create mold body, core and cavity.
Lesson
1 year ago
ENG
JPN
Create a pattern of one or more features or bodies in one or two circular directions. The circular direction is based on a cylindrical or conical face, a circular or linear edge, centerline or axis. Spacing of instances can be controlled in different ways. Create circular patterns of existing features. Vary spacing and range.
Lesson
5 months ago
ENG
FRA
DEU
JPN
CHS
Insert a reducing outlet tee into an existing route and orient it using keyboard shortcuts and a triad. Use the Auto Route tool to connect the pipes resulting from the additional feature. Add in-line fittings to existing routes. Use keyboard shortcuts and the triad to orient and position an in-line fitting.
Lesson
3 years ago
ENG
JPN
Create and use a custom route specification template using the Routing Library Manager. Specify size and schedule of pipe segments. Select pipes and elbows from the Piping and Tubing Database. Insert route components with route specification templates.
Lesson
2 years ago
ENG
JPN
Use extruded, revolved, and swept surfaces to create geometry. Trim, extend, knit, and thicken the surfaces to finish the thin-walled model. Extrude a sketch to create a surface. Revolve a sketch about an axis to create a surface. Trim a surface using a sketch or another surface as the trim tool. Sweep an open profile along a path to create a surface. Combine multiple surfaces into a single body using knit surfaces. Thicken a surface body to create a solid body.
Lesson
1 year ago
ENG
JPN