Анализ частей крупной сборки для экономии времени и получение точных результатов с помощью подмоделирования. Создание исследования подмодели из родительского исследования. Автоматический перенос нагрузок в исследование подмодели. Экономия времени и вычислительных ресурсов без потери точности результатов. Использование eDrawings для сохранения результатов.
Lesson
3 мес. назад
ENG
Setup, run and postprocess a harmonic simulation. Understand and practice the frequency domain excitation definition. Practice postprocessing results from the harmonic study. Setup, run and postprocess a harmonic study Use the mass participation factor to select a sufficient number of natural frequencies Optimize the finite element mesh for dynamic simulation Define the harmonic load in the frequency domain Postprocess results from the harmonic study
Lesson
3 мес. назад
ENG
Setup, run and postprocess a dynamic simulation with the base motion shock excitation. Understand the optimum mesh design, and get more familiar with the estimation of the minimum number of natural frequencies. Understand the basics of damping. Setup, run and postprocess a transient study Define base excitation shock load Use the mass participation factor to select a sufficient number of natural frequencies Optimize the finite element mesh for dynamic simulation Define structural damping Calculate the maximum time step Use remote mass to simplify the model
Lesson
3 мес. назад
ENG
Setup initial dynamic simulation, solve and postprocess the results. Understand the importance of natural frequencies in dynamic simulations. Compare the dynamic and static results. Setup, run and postprocess a basic transient study Calculate a sufficient number of natural frequencies Use the mass participation factor to estimate a sufficient number of natural frequencies Run dynamic simulation for slow and fast forces, and compare their results
Lesson
3 мес. назад
ENG
Review the basic functionality of the SOLIDWORKS Dynamics module. Show activation of SOLIDWORKS Simulation Add-In. Review the available modules for specific dynamic load times.
Lesson
3 мес. назад
ENG
Изучение концепции сходимости сетки на примере того, как размер элементов влияет на напряжения, деформации и перемещения. Оценка влияния глобального размера элемента на результаты. Применение элементов управления сеткой в определенных точках. Основные сведения о том, как острые углы могут привести к концентрации напряжений.
Lesson
3 мес. назад
ENG
Обзор пользовательского интерфейса Simulation и описание процесса установки для простой детали. Запуск моделирования и анализ результатов. Изучение пользовательского интерфейса Simulation. Применение креплений, материалов и нагрузок. Запуск моделирования и анализ модели на предмет напряжения и перемещения.
Lesson
3 мес. назад
ENG
Использование оболочек для моделирования тонких структур. Создание оболочек на тонких структурах с помощью менеджера оболочки. Применение симметричных креплений для уменьшения вычислительных усилий.
Lesson
1 год назад
ENG
Examine the motion of a catapult as it is loaded and throws a projectile. Add solid bodies contact, add a spring and apply friction. Determine torque required to rotate the crank and load the catapult. Determine the displacement of the loading spring. Study the effect of contact friction on the motion of the projectile.
Lesson
2 лет назад
ENG
SOLIDWORKS Motion is a virtual prototyping tool for engineers and designers interested in understanding the performance of their assemblies. Perform a basic motion analysis using SOLIDWORKS Motion. Simulate the weight of a vehicle on the jack. Determine toque and power required to lift it.
Lesson
2 лет назад
ENG
Mesh the Flow Simulation geometry using manual meshing approach. Control Basic mesh settings. Apply manual mesh setting and options. Define control planes. Define and apply local mesh controls. Plot mesh on cut plots.
Lesson
2 лет назад
ENG
Mesh the Flow Simulation geometry using automated meshing approach. Understand the Basic mesh, and Initial mesh concepts. Control the Global Initial mesh refinement level. Analyze the Minimum Gap Size feature value as the project settings change. Plot mesh on cut plots.
Lesson
2 лет назад
ENG
Run SOLIDWORKS Flow simulation and monitor it. Postprocess Flow simulation results. Launch the SOLIDWORKS Flow simulation and monitor it in the solver window. Monitor execution of the simulation in the solver window. Postprocess results using cut plots, surface plots, flow trajectories. Create 2D graphs from the calculated results, extract results on desired geometrical entities.
Lesson
2 лет назад
ENG
Build the SOLIDWORKS Flow Simulation project. Use Wizard to define Flow Simulation project. Define boundary conditions. Define goals. Mesh the model geometry.
Lesson
2 лет назад
ENG
Prepare SOLIDWORKS geometry for Flow Simulation analysis. Create lids manually. Create lids using the Lid Creation tool. Check if the geometry is water tight for internal flow analysis. Detect leaks in improperly sealed geometry.
Lesson
2 лет назад
ENG
Learn about SOLIDWORKS Flow Simulation software. View sample applications from the real world. View sample real world examples where the software was used.
Lesson
2 лет назад
ENG
Обзор возможностей пакета SOLIDWORKS Simulation и всех модулей. Анализ теплообмена и потока жидкости с помощью SOLIDWORKS Flow. Использование Sustainability для уменьшения экологического эффекта проектов. Анализ напряжение-деформация с помощью SOLIDWORKS Simulation. Анализ динамики жестких тел в SOLIDWORKS Motion. Просмотр видов заполнения пластмассовых литых детали с помощью SOLIDWORKS Plastics.
Lesson
2 лет назад
ENG
Simulate a mechanism placing an object into a box and a cover on the box. Apply servo motors. Add proximity sensors. Create and run event based motion study.
Lesson
2 лет назад
ENG
Generate a cam profile based on an input follower displacement from a data set. Define a motion of a follower using Data Points. Generate a cam profile using Trace Path. Verify the generated cam profile.
Lesson
2 лет назад
ENG
Оптимизация проектов за счет уменьшения веса модели через изменение ее размеров. Применение параметров и ограничений для оптимизации проекта и реализации поставленных целей. Использование исследований проектирования в Simulation.
Lesson
3 лет назад
ENG
Introduction to the material nonlinearity, namely metal plasticity. Effect of mesh quality on the quality of the numerical stress results. Solve problem with linear small displacement solution and identify a need for the nonlinear solution due to high stress. Define nonlinear study boundary conditions and loads. Define nonlinear material model with von Mises plasticity. Use simplified bi-linear plasticity material model. Review the stress and displacement results at various times. Study effect of mesh quality on the quality of the stress results. Use the mesh sectioning feature to review stress distribution within the bodies.
Lesson
3 лет назад
ENG
Introduction to the force control and displacement control methods in nonlinear module. Experience and resolve solution instabilities when solving nonlinear problems. Define nonlinear study boundary conditions and loads. Stabilize force control method to arrive to a final solution. Solve the problem using the displacement control method. Adjust boundary conditions for the displacement control method. Compare nonlinear results from the force control, and the displacement control methods.
Lesson
3 лет назад
ENG
Review the difference between small displacement linear, and large displacement nonlinear analyses. Introduce the concept of time curves, and discuss basic options. Solve small displacement linear analysis to demonstrate inaccurate solution. Define a nonlinear simulation study. Use time curves to control variation of the nonlinear loading. Use fixed increment stepping, and autostepping stepping procedures to solve the nonlinear problem. Postprocess results of the nonlinear simulation. Compare results from nonlinear studies with various setup parameters.
Lesson
3 лет назад
ENG
Review the basic functionality of the SOLIDWORKS Nonlinear module. Show activation of SOLIDWORKS Simulation Add-In. Learn three basic nonlinear phenomena in engineering calculations. Review of control methods available in the module. Review of basic material models available in the module.
Lesson
3 лет назад
ENG