Jak analyzovat část větší sestavy a tím ušetřit čas a získat přesnější výsledky za použití dílčího modelování. Vytvoření studie dílčího modelu z nadřazené studie. Jak se zatížení automaticky přenesou do studie dílčího modelu. Úspora času a výpočetních prostředků při zachování přesných výsledků. Použití eDrawings k uložení výsledků.
Lesson
3 měsíců před
ENG
Setup, run and postprocess a harmonic simulation. Understand and practice the frequency domain excitation definition. Practice postprocessing results from the harmonic study. Setup, run and postprocess a harmonic study Use the mass participation factor to select a sufficient number of natural frequencies Optimize the finite element mesh for dynamic simulation Define the harmonic load in the frequency domain Postprocess results from the harmonic study
Lesson
3 měsíců před
ENG
Setup, run and postprocess a dynamic simulation with the base motion shock excitation. Understand the optimum mesh design, and get more familiar with the estimation of the minimum number of natural frequencies. Understand the basics of damping. Setup, run and postprocess a transient study Define base excitation shock load Use the mass participation factor to select a sufficient number of natural frequencies Optimize the finite element mesh for dynamic simulation Define structural damping Calculate the maximum time step Use remote mass to simplify the model
Lesson
3 měsíců před
ENG
Setup initial dynamic simulation, solve and postprocess the results. Understand the importance of natural frequencies in dynamic simulations. Compare the dynamic and static results. Setup, run and postprocess a basic transient study Calculate a sufficient number of natural frequencies Use the mass participation factor to estimate a sufficient number of natural frequencies Run dynamic simulation for slow and fast forces, and compare their results
Lesson
3 měsíců před
ENG
Review the basic functionality of the SOLIDWORKS Dynamics module. Show activation of SOLIDWORKS Simulation Add-In. Review the available modules for specific dynamic load times.
Lesson
3 měsíců před
ENG
Tento modul představuje koncept konvergence sítě na tom, jak velikost prvků ovlivňuje napětí, deformace a posunutí. Jak změna globální velikosti prvku ovlivňuje výsledky. Jak použít zjemnění sítě na konkrétních místech. Jak mohou ostré rohy způsobovat koncentraci napětí.
Lesson
3 měsíců před
ENG
Tento modul představuje uživatelské rozhraní Simulation a provede vás procesem přípravy jednoduchého dílu. Potom se provede simulace a analyzují výsledky. Uživatelské rozhraní Simulation. Použití přípravků, materiálů a zatížení. Provedení simulace a analýza modelu s ohledem na napětí a posunutí.
Lesson
3 měsíců před
ENG
Jak použít skořepiny k modelování tenkých struktur. Vytvoření skořepin na tenkých strukturách s použitím správce skořepin. Použití symetrických uchycení k redukci náročnosti na výpočet.
Lesson
1 rok před
ENG
Examine the motion of a catapult as it is loaded and throws a projectile. Add solid bodies contact, add a spring and apply friction. Determine torque required to rotate the crank and load the catapult. Determine the displacement of the loading spring. Study the effect of contact friction on the motion of the projectile.
Lesson
2 roků před
ENG
SOLIDWORKS Motion is a virtual prototyping tool for engineers and designers interested in understanding the performance of their assemblies. Perform a basic motion analysis using SOLIDWORKS Motion. Simulate the weight of a vehicle on the jack. Determine toque and power required to lift it.
Lesson
2 roků před
ENG
Mesh the Flow Simulation geometry using manual meshing approach. Control Basic mesh settings. Apply manual mesh setting and options. Define control planes. Define and apply local mesh controls. Plot mesh on cut plots.
Lesson
2 roků před
ENG
Mesh the Flow Simulation geometry using automated meshing approach. Understand the Basic mesh, and Initial mesh concepts. Control the Global Initial mesh refinement level. Analyze the Minimum Gap Size feature value as the project settings change. Plot mesh on cut plots.
Lesson
2 roků před
ENG
Run SOLIDWORKS Flow simulation and monitor it. Postprocess Flow simulation results. Launch the SOLIDWORKS Flow simulation and monitor it in the solver window. Monitor execution of the simulation in the solver window. Postprocess results using cut plots, surface plots, flow trajectories. Create 2D graphs from the calculated results, extract results on desired geometrical entities.
Lesson
2 roků před
ENG
Build the SOLIDWORKS Flow Simulation project. Use Wizard to define Flow Simulation project. Define boundary conditions. Define goals. Mesh the model geometry.
Lesson
2 roků před
ENG
Prepare SOLIDWORKS geometry for Flow Simulation analysis. Create lids manually. Create lids using the Lid Creation tool. Check if the geometry is water tight for internal flow analysis. Detect leaks in improperly sealed geometry.
Lesson
2 roků před
ENG
Learn about SOLIDWORKS Flow Simulation software. View sample applications from the real world. View sample real world examples where the software was used.
Lesson
2 roků před
ENG
Představení sady produktů SOLIDWORKS Simulation a všech jejích modulů. Analýza přenosu tepla a proudění tekutin s použitím SOLIDWORKS Flow. Použití softwaru Sustainability k omezení dopadu vašich návrhů na životní prostředí. Analýza napětí a deformace s použitím SOLIDWORKS Simulation. Analýza dynamiky tuhého tělesa s použitím SOLIDWORKS Motion. Zobrazení vzorců plnění lisovaných plastových dílů s použitím SOLIDWORKS Plastics.
Lesson
2 roků před
ENG
Simulate a mechanism placing an object into a box and a cover on the box. Apply servo motors. Add proximity sensors. Create and run event based motion study.
Lesson
2 roků před
ENG
Generate a cam profile based on an input follower displacement from a data set. Define a motion of a follower using Data Points. Generate a cam profile using Trace Path. Verify the generated cam profile.
Lesson
2 roků před
ENG
Jak optimalizovat návrhy a snížit hmotnost modelu prostřednictvím variace rozměrů modelu. Použití parametrů a omezení pro optimalizaci návrhu a splnění cílů. Použití designových studií v softwaru Simulation.
Lesson
3 roků před
ENG
Introduction to the material nonlinearity, namely metal plasticity. Effect of mesh quality on the quality of the numerical stress results. Solve problem with linear small displacement solution and identify a need for the nonlinear solution due to high stress. Define nonlinear study boundary conditions and loads. Define nonlinear material model with von Mises plasticity. Use simplified bi-linear plasticity material model. Review the stress and displacement results at various times. Study effect of mesh quality on the quality of the stress results. Use the mesh sectioning feature to review stress distribution within the bodies.
Lesson
3 roků před
ENG
Introduction to the force control and displacement control methods in nonlinear module. Experience and resolve solution instabilities when solving nonlinear problems. Define nonlinear study boundary conditions and loads. Stabilize force control method to arrive to a final solution. Solve the problem using the displacement control method. Adjust boundary conditions for the displacement control method. Compare nonlinear results from the force control, and the displacement control methods.
Lesson
3 roků před
ENG
Review the difference between small displacement linear, and large displacement nonlinear analyses. Introduce the concept of time curves, and discuss basic options. Solve small displacement linear analysis to demonstrate inaccurate solution. Define a nonlinear simulation study. Use time curves to control variation of the nonlinear loading. Use fixed increment stepping, and autostepping stepping procedures to solve the nonlinear problem. Postprocess results of the nonlinear simulation. Compare results from nonlinear studies with various setup parameters.
Lesson
3 roků před
ENG
Review the basic functionality of the SOLIDWORKS Nonlinear module. Show activation of SOLIDWORKS Simulation Add-In. Learn three basic nonlinear phenomena in engineering calculations. Review of control methods available in the module. Review of basic material models available in the module.
Lesson
3 roků před
ENG