I have been trying to figure out the use of these probes/sensors now for wayyy too long and have to admit defeat. My goal is to have the displacement in X displayed in this particular spot as a read out on the sensor, but when I save the probe as a sensor I get nothing???
SOLIDWORKS Forums
1 hour ago
I am trying to do a drop test on an assembly which has 7 parts and am facing a lot of challenges on the meshing. Can someone please help me troubleshoot this? The design is a packaging for a ceramic mug which also has other accessories present in the box. I will attach the files if needed.
SOLIDWORKS Forums
2 hours ago
Linear motor problem. Attached is an assembly with two parts. I've been messing with this in a larger assembly for the last couple days.
SOLIDWORKS Forums
3 hours ago
I am trouble getting any turbulent flow trajectories in a model of water flow through a cylindrical tube, with an inlet volume/pipe diameter that gives a Reynolds number that should easily be in the turbulent range. I selected "turbulent only" in the simulation wizard. Yet, when visualizing the flow trajectories for velocity, I only see what appear to be laminar flows (in straight lines parallel to the long cylinder axis). This happens regardless of whether I model the inner pipe surface as a
SOLIDWORKS Forums
1 day ago
I want to see the flow profile for my microfluidic device. I am struggling with the boundary conditions. The inlet chamber will be injected with a syringe.
SOLIDWORKS Forums
1 day ago
elbow thrust force simulation hello guys , i'm working on pressure reducer station , my job is to find the thrust forces on the elbows during the water flows and change it direction . so i can design a support structural steel to hold the pipe station .
SOLIDWORKS Forums
1 day ago
Wind Tunnel Flow Simulation I've created a wind tunnel for a school project in SW and am trying to run a flow simulation to test the maximum achievable wind speed within the test section. I know the motor our group is going to use but can't find anything close to the size I need in the available axial fans section of SW.
SOLIDWORKS Forums
1 day ago
I have a large assembly I have created for simulation. Now due to it's size, the original meshing attempts were taking forever. I figured I could just draw a rectangle and cut away a significant chunk of the assembly and then try to mesh.
SOLIDWORKS Forums
1 day ago
Static Simulation I have a problem ı wanna do static analysis of car tire so ı tried all the ways but this happened errorIMG_20181209_215421.jpg
SOLIDWORKS Forums
2 days ago
Chain array motion? Can you make a chain array move in a motion study around a belt? Picture a cleated conveyor belt?
SOLIDWORKS Forums
2 days ago
Short version: I'm getting this error: "No element surface defined on a Pin joint" Does anyone know what it means? Long version: I ran the FEA then made some changes (but no changes to any of the pins or pinned surfaces). Now I am getting this error message.
SOLIDWORKS Forums
2 days ago
The members are cut out of 3x3-inch aluminum angle. The structure is a rectangular box about 72-inch sides, with lots of bracing and supports all over the place. The small features are important, but the structure is big.
SOLIDWORKS Forums
2 days ago
I have an assembly as on the attached animation: there is ring between the two springs and the question is the stress/deformation. Setup: only the ring has a von Mises plastic material model the rest are linar (no penetration with friction everywhere)
SOLIDWORKS Forums
2 days ago
I am trying to make an animation of a cam and follower mechanism and I have defined a cam mate between the two parts,namely the cam and follower.The cam has several faces and I chose one of them as the cam face.The problem is that when I make an animation out of it the follower will attach to that single face that I defined as my cam face and so it doesn't simulate a proper movement as you can see in the photo I have attached.I did attach my files as well.Please tell me what is wrong with work.
SOLIDWORKS Forums
3 days ago
Static Simulation Error ( PCG iterative solver stopped. Status Code: 10 Jacobian _ singular. May have bad ( distorted ) elements. )
SOLIDWORKS Forums
3 days ago
Point force I avoid point forces in order to avoid singularities. Instead I divide the surface to make a patch of known area and apply pressure.
SOLIDWORKS Forums
3 days ago
I've set global contact for this simulation but the stress distribution looks not reasonable. Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
3 days ago
Bearing fixture I am simulating a rotating shaft mounted by two pulleys when setting bearing fixtures as B.C, S.W always gives me wrong force connectors results
SOLIDWORKS Forums
5 days ago
'Mesh generating Fail' every time I am running result calculation to study simulation in motion analysis I am getting this error. I could not see any reason why this message pops up while running the mesh generations.? Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
5 days ago
Problem with Star Solver Bekomme immer die Fehlermeldung:Der SOLIDWORKS Simulation-Solver wurde unerwartet beendet. Grund: Ausnahmecode 0xc0000005 an Adresse 0x140c1a940 in: Star.exe file version 27,5,0,8 ausgegeben.
SOLIDWORKS Forums
5 days ago
Anhand von einfachen Beispielen lernen Sie in 22 Minuten, welche Produktvalidierungen Sie für die Bereiche Produktentwicklung und Fertigung an Ihrem CAD-Modell durchführen können. Wann? Freitag, 14. Dezember 2018, 13:30 Uhr.
SOLIDWORKS DEUTSCH Blog
6 days ago
I'm somewhat new with the fea, but I have an assembly where we have some testing we'd like to do. One would just be a housing, one would be the housing & two other objects, & one would be the housing and around 1/2 dozen components. Can I do these all in the same assembly, with configurations, suppressing the components? I would think that Fea would consider suppressed components not there, but I'm not sure.
SOLIDWORKS Forums
6 days ago
Profitieren Sie von unseren attraktiven Angeboten zum Jahresende 2018 und sparen Sie bis zu € 7.500,-! Nur noch 16 Tage: Sonderkonditionen auf unser gesamtes Lösungsportfolio – SOLIDWORKS Plus, Simulation oder Mechatronik. Ob Neueinstieg, Umstieg oder Upgrade, FORDERN SIE ONLINE IHR BESTES ANGEBOT AN oder RUFEN SIE UNS JETZT AN: +49 (0) 89 960 948-400 Beschleunigen Sie mit den jetzt verfügbaren SOLIDWORKS Aktionspaketen Ihren gesamten Entwicklungs- und Fertigungszyklus – die Vorteile auf einen
SOLIDWORKS DEUTSCH Blog
6 days ago
Long time SW user, first time using this forum. I work with a lot of imported geometry from contract mfgrs and historically this was the issue (coworkers dont always import correctly as they dont use Flow). Part was re-imported from native, Flow run on only part and meshed & solved as expected, inserted into assy with other imported parts (that work perfectly), and Flow mesh & solver ignore part. Part is single solid with no surfaces.
SOLIDWORKS Forums
6 days ago