I have all my music on an external hard drive. Streaming here is a big island no-no except for youtube. Both of these are likely to be taken away soon too (IT nazis).
SOLIDWORKS Forums
11 minutes ago
Why...does SolidWorks, when I initiate a cut, more often than not go away from the part and give me the "intended cut does not intersect the model?? If the software knows where the model is, why doesn't it default to the valid direction??
SOLIDWORKS Forums
49 minutes ago
SWIFT = SolidWorks International Forum Team How many times do you see a great thread get trashed or hijacked for various reasons and I'll take the "Stand" and say I'm the worst for doing that.. So when I'm acting stupid tell me to trash it here, get it?
SOLIDWORKS Forums
56 minutes ago
If I have only one part in assembly orbiting is smooth and GPU meter shows about 20%. When I put more parts (let say 40 parts) in assembly GPU meter gets down to about 4% and orbiting is slow/lagging. I used before SW2017 and with that assemblies (several hundreds parts) worked fine, orbiting was smooth and no lagging but with SW2019 I cannot orbit (extremely slow) these same assemblies anymore. Is there some settings that I have missed?
SOLIDWORKS Forums
1 hour ago
Solidworks tutorials Can anyone recommend any good tutorials I can do whilst being stuck in hospital? Preferably something fun like cars or boats etc that I can get some good renders from.
SOLIDWORKS Forums
3 hours ago
Non-technical Thread: Furry Friends Sometimes you just want to share a picture of your pets (Whatever you may call them: Furry Friends, Fur-kids, Interns, and so on.)
SOLIDWORKS Forums
3 hours ago
Non-technical Thread: Favorite Quotes Let's try to keep this thread on topic. Just post your favorite quotes.
SOLIDWORKS Forums
3 hours ago
After seeing the good discussions here (to list only a few):Will the Top Ten List be handled differently this year?,https://forum.solidworks.com/message/689652#comment-689652,Simplify the Enhancement Request System and Tie it Into the ForumsI wanted to summarize how I think the ideas are viewed before and after voting. The submitted ideas are typically all over the map or chart in this case.
SOLIDWORKS Forums
3 hours ago
This question is directed atJim Wilkinson,Jody Stilesand anyone else at SWX that is in such a position to answer. In the past the Top Ten Wish List has been a very active place, but it has only been temporary. It opens sometimes around the rollouts (October?) and closes for new contributions in mid-December (I think), butthe problem I see is that it completely vanishes from this forum around the end of SWX World.
SOLIDWORKS Forums
4 hours ago
Was working on a part last night, dutifully saving every 20 mins. Went to reopen the file today and it was noted to have last been modified/saved hours prior to the time I remember finishing up and clicking the save button for the last time. Is there any way of rectifying this or must I accept my fate and redo the whole thing?
SOLIDWORKS Forums
4 hours ago
I am working on an Anthropometric study for a device I am designing. Does anyone know where I can find a freed CAD model of the human body? Have you tried3D Content Central?
SOLIDWORKS Forums
4 hours ago
detail question Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
5 hours ago
Respectable forum members. A great accumulation of knowledge and many experienced people,
SOLIDWORKS Forums
5 hours ago
Yep, it's definitely possible............ Actually instead of rings, I have helix that I want to make a circular pattern of 16 helix. But I don't know how to make the image of one coil and arrange them in a circular pattern like in the figure you shown.
SOLIDWORKS Forums
6 hours ago
24.0GB Dual-Channel Unknown @ 1063MHz (15-15-15-36) ,hardware requirements
SOLIDWORKS Forums
7 hours ago
Non-Technical thread:Favorite (clean) jokes I know we've had some great favorite quotes, but sometimes I just need a laugh. So, I'm proposing that everyone post their favorite joke.
SOLIDWORKS Forums
16 hours ago
On behalf of the SOLIDWORKS team, thank you to everyone for ideas submitted to the SOLIDWORKS World 2019 Top Ten List. We are happy to see that even though the idea submissions window was a little shorter this year, the number of submissions is on par with previous years. This shows a lot of enthusiasm!
SOLIDWORKS Forums
18 hours ago
Hi all. I've tried my hardest to find a solution to this issue on these forums, but nothing is fully helping (though there is a lot of helpful advice on here!). I'm hoping someone out there may have a suggestion for a fix I've yet to try.
SOLIDWORKS Forums
19 hours ago
I have tried to do a clean installation, improve performance by disabling some visual effects on windows and disabling all programs like antivirus ecc.... I have the same computer in another position with the same configurations ( except for CPU that is a Intel I7-7600) without any kind of problem like it.
SOLIDWORKS Forums
21 hours ago
I used an image to draw an object but now need to change to orientation so it matches the centre line X axis - ie the two points (feet) need to sit along the centre line Im not quite clear what I need to search for in the help so thought a picture of part of the object would maybe enable someone to point me in the right direction
SOLIDWORKS Forums
21 hours ago
Hi everyone. I have been using draftisght for about a year now and recently started having a problem with editing text boxes. When I double click on a textbox to edit the text draftisight auto zooms in on the textbox. Then when I click outside the textbox it auto zooms back out.
SOLIDWORKS Forums
1 day ago
Check out this post Geoffrey! translucent screen in solidworks 2014
SOLIDWORKS Forums
1 day ago
I don't know if the Microsoft version matters or not. I am also concerned about making using a Macro to make things easier and faster after linking SW BOM to Excel. Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
1 day ago
I am getting really bad edge lines on the models as you can see in image. When I zoom out these models just go completely black and are super ugly. I have gone into Options>Document Properties>Image Quality and cranked anything or ticked anything that can possibly relate to a better image. Also in Performance.
SOLIDWORKS Forums
1 day ago