Hi, I am a student and for my final year project I need to model some golf clubs. I am looking to do a simple static simulation on them in solidworks. I am new to surface modelling and simulation so would appreciate any help with my modelling and simulation, I have attached the parts/assembly.
SOLIDWORKS Forums
4 heures il y a
Static Simulation Error ( PCG iterative solver stopped. Status Code: 10 Jacobian _ singular. May have bad ( distorted ) elements. )
SOLIDWORKS Forums
22 heures il y a
I would like to utilize SimulationXpress to analyze the stresses on a rotating pipe. I can calculate the radial (centrifugal) force and apply it on the inside wall with a radially outward vector, also calculate the hoop force though to apply the force vector would require a cylindrical coordinate system - which I am having trouble locating in SW and the axial force at the moment is not of interest. Most folks would use thefull version of SOLIDWORKS Simulation instead of SOLIDWORKS
SOLIDWORKS Forums
23 heures il y a
Wrong results I simulate the heating of a steel brick with a side dimensions of 5x5x7mm.I heat one side (3558K).But the opposite side remains completely cold (293.2K).In my opinion, this is unrealistic.What am I doing wrong?
SOLIDWORKS Forums
1 jour il y a
My problem is, I am going to apply pressure (caused by soil) to outside surface of pipe, but I don't know the equation of this non-linear pressure. or , is there better way to apply soil pressure upon a cylinder surface? Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
1 jour il y a
I used H-adaptive to attempt to get accurate results for static analysis. After 5 loops' calculation software said that the calculation has achieved 98% accuracy, so I thought the stress calculated must be accurate enough. But it turned out that my maximum stress is much greater than material's yield strength, which tells me I should consider using Non-linear and the maximum stress value may not be correct.
SOLIDWORKS Forums
2 jours il y a
The members are cut out of 3x3-inch aluminum angle. The structure is a rectangular box about 72-inch sides, with lots of bracing and supports all over the place. The small features are important, but the structure is big.
SOLIDWORKS Forums
3 jours il y a
I have been trying to figure out the use of these probes/sensors now for wayyy too long and have to admit defeat. My goal is to have the displacement in X displayed in this particular spot as a read out on the sensor, but when I save the probe as a sensor I get nothing???
SOLIDWORKS Forums
4 jours il y a
I am trying to do a drop test on an assembly which has 7 parts and am facing a lot of challenges on the meshing. Can someone please help me troubleshoot this? The design is a packaging for a ceramic mug which also has other accessories present in the box. I will attach the files if needed.
SOLIDWORKS Forums
5 jours il y a
Linear motor problem. Attached is an assembly with two parts. I've been messing with this in a larger assembly for the last couple days.
SOLIDWORKS Forums
5 jours il y a
I am trouble getting any turbulent flow trajectories in a model of water flow through a cylindrical tube, with an inlet volume/pipe diameter that gives a Reynolds number that should easily be in the turbulent range. I selected "turbulent only" in the simulation wizard. Yet, when visualizing the flow trajectories for velocity, I only see what appear to be laminar flows (in straight lines parallel to the long cylinder axis). This happens regardless of whether I model the inner pipe surface as a
SOLIDWORKS Forums
5 jours il y a
I want to see the flow profile for my microfluidic device. I am struggling with the boundary conditions. The inlet chamber will be injected with a syringe.
SOLIDWORKS Forums
5 jours il y a
elbow thrust force simulation hello guys , i'm working on pressure reducer station , my job is to find the thrust forces on the elbows during the water flows and change it direction . so i can design a support structural steel to hold the pipe station .
SOLIDWORKS Forums
6 jours il y a
Wind Tunnel Flow Simulation I've created a wind tunnel for a school project in SW and am trying to run a flow simulation to test the maximum achievable wind speed within the test section. I know the motor our group is going to use but can't find anything close to the size I need in the available axial fans section of SW.
SOLIDWORKS Forums
6 jours il y a
I have a large assembly I have created for simulation. Now due to it's size, the original meshing attempts were taking forever. I figured I could just draw a rectangle and cut away a significant chunk of the assembly and then try to mesh.
SOLIDWORKS Forums
6 jours il y a
Static Simulation I have a problem ı wanna do static analysis of car tire so ı tried all the ways but this happened errorIMG_20181209_215421.jpg
SOLIDWORKS Forums
6 jours il y a
Chain array motion? Can you make a chain array move in a motion study around a belt? Picture a cleated conveyor belt?
SOLIDWORKS Forums
6 jours il y a
Short version: I'm getting this error: "No element surface defined on a Pin joint" Does anyone know what it means? Long version: I ran the FEA then made some changes (but no changes to any of the pins or pinned surfaces). Now I am getting this error message.
SOLIDWORKS Forums
6 jours il y a
I have an assembly as on the attached animation: there is ring between the two springs and the question is the stress/deformation. Setup: only the ring has a von Mises plastic material model the rest are linar (no penetration with friction everywhere)
SOLIDWORKS Forums
7 jours il y a
I am trying to make an animation of a cam and follower mechanism and I have defined a cam mate between the two parts,namely the cam and follower.The cam has several faces and I chose one of them as the cam face.The problem is that when I make an animation out of it the follower will attach to that single face that I defined as my cam face and so it doesn't simulate a proper movement as you can see in the photo I have attached.I did attach my files as well.Please tell me what is wrong with work.
SOLIDWORKS Forums
8 jours il y a
Point force I avoid point forces in order to avoid singularities. Instead I divide the surface to make a patch of known area and apply pressure.
SOLIDWORKS Forums
8 jours il y a
I've set global contact for this simulation but the stress distribution looks not reasonable. Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
8 jours il y a
Bearing fixture I am simulating a rotating shaft mounted by two pulleys when setting bearing fixtures as B.C, S.W always gives me wrong force connectors results
SOLIDWORKS Forums
9 jours il y a
'Mesh generating Fail' every time I am running result calculation to study simulation in motion analysis I am getting this error. I could not see any reason why this message pops up while running the mesh generations.? Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
10 jours il y a