Trying to run a Flow simulation with a very simple Two-Resistor Component placed on a metal socket. Two-Resistor Component is a Pre-Defined template from the Engineering Database.
SOLIDWORKS Forums
5 horas atrás
Hi, I am a student and for my final year project I need to model some golf clubs. I am looking to do a simple static simulation on them in solidworks. I am new to surface modelling and simulation so would appreciate any help with my modelling and simulation, I have attached the parts/assembly.
SOLIDWORKS Forums
13 horas atrás
Chain array motion? Can you make a chain array move in a motion study around a belt? Picture a cleated conveyor belt?
SOLIDWORKS Forums
18 horas atrás
Static Simulation Error ( PCG iterative solver stopped. Status Code: 10 Jacobian _ singular. May have bad ( distorted ) elements. )
SOLIDWORKS Forums
1 dia atrás
I would like to utilize SimulationXpress to analyze the stresses on a rotating pipe. I can calculate the radial (centrifugal) force and apply it on the inside wall with a radially outward vector, also calculate the hoop force though to apply the force vector would require a cylindrical coordinate system - which I am having trouble locating in SW and the axial force at the moment is not of interest. Most folks would use thefull version of SOLIDWORKS Simulation instead of SOLIDWORKS
SOLIDWORKS Forums
1 dia atrás
Wrong results I simulate the heating of a steel brick with a side dimensions of 5x5x7mm.I heat one side (3558K).But the opposite side remains completely cold (293.2K).In my opinion, this is unrealistic.What am I doing wrong?
SOLIDWORKS Forums
2 dias atrás
My problem is, I am going to apply pressure (caused by soil) to outside surface of pipe, but I don't know the equation of this non-linear pressure. or , is there better way to apply soil pressure upon a cylinder surface? Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
2 dias atrás
I used H-adaptive to attempt to get accurate results for static analysis. After 5 loops' calculation software said that the calculation has achieved 98% accuracy, so I thought the stress calculated must be accurate enough. But it turned out that my maximum stress is much greater than material's yield strength, which tells me I should consider using Non-linear and the maximum stress value may not be correct.
SOLIDWORKS Forums
3 dias atrás
The members are cut out of 3x3-inch aluminum angle. The structure is a rectangular box about 72-inch sides, with lots of bracing and supports all over the place. The small features are important, but the structure is big.
SOLIDWORKS Forums
4 dias atrás
I have been trying to figure out the use of these probes/sensors now for wayyy too long and have to admit defeat. My goal is to have the displacement in X displayed in this particular spot as a read out on the sensor, but when I save the probe as a sensor I get nothing???
SOLIDWORKS Forums
5 dias atrás
I am trying to do a drop test on an assembly which has 7 parts and am facing a lot of challenges on the meshing. Can someone please help me troubleshoot this? The design is a packaging for a ceramic mug which also has other accessories present in the box. I will attach the files if needed.
SOLIDWORKS Forums
5 dias atrás
Linear motor problem. Attached is an assembly with two parts. I've been messing with this in a larger assembly for the last couple days.
SOLIDWORKS Forums
5 dias atrás
I am trouble getting any turbulent flow trajectories in a model of water flow through a cylindrical tube, with an inlet volume/pipe diameter that gives a Reynolds number that should easily be in the turbulent range. I selected "turbulent only" in the simulation wizard. Yet, when visualizing the flow trajectories for velocity, I only see what appear to be laminar flows (in straight lines parallel to the long cylinder axis). This happens regardless of whether I model the inner pipe surface as a
SOLIDWORKS Forums
6 dias atrás
I want to see the flow profile for my microfluidic device. I am struggling with the boundary conditions. The inlet chamber will be injected with a syringe.
SOLIDWORKS Forums
6 dias atrás
elbow thrust force simulation hello guys , i'm working on pressure reducer station , my job is to find the thrust forces on the elbows during the water flows and change it direction . so i can design a support structural steel to hold the pipe station .
SOLIDWORKS Forums
6 dias atrás
Wind Tunnel Flow Simulation I've created a wind tunnel for a school project in SW and am trying to run a flow simulation to test the maximum achievable wind speed within the test section. I know the motor our group is going to use but can't find anything close to the size I need in the available axial fans section of SW.
SOLIDWORKS Forums
6 dias atrás
I have a large assembly I have created for simulation. Now due to it's size, the original meshing attempts were taking forever. I figured I could just draw a rectangle and cut away a significant chunk of the assembly and then try to mesh.
SOLIDWORKS Forums
7 dias atrás
Static Simulation I have a problem ı wanna do static analysis of car tire so ı tried all the ways but this happened errorIMG_20181209_215421.jpg
SOLIDWORKS Forums
7 dias atrás
Short version: I'm getting this error: "No element surface defined on a Pin joint" Does anyone know what it means? Long version: I ran the FEA then made some changes (but no changes to any of the pins or pinned surfaces). Now I am getting this error message.
SOLIDWORKS Forums
7 dias atrás
I have an assembly as on the attached animation: there is ring between the two springs and the question is the stress/deformation. Setup: only the ring has a von Mises plastic material model the rest are linar (no penetration with friction everywhere)
SOLIDWORKS Forums
8 dias atrás
I am trying to make an animation of a cam and follower mechanism and I have defined a cam mate between the two parts,namely the cam and follower.The cam has several faces and I chose one of them as the cam face.The problem is that when I make an animation out of it the follower will attach to that single face that I defined as my cam face and so it doesn't simulate a proper movement as you can see in the photo I have attached.I did attach my files as well.Please tell me what is wrong with work.
SOLIDWORKS Forums
8 dias atrás
Point force I avoid point forces in order to avoid singularities. Instead I divide the surface to make a patch of known area and apply pressure.
SOLIDWORKS Forums
9 dias atrás
I've set global contact for this simulation but the stress distribution looks not reasonable. Jive Software Version: 2018.10.0.1_jx, revision: 20181102150941.22e8dc7.release_2018.10.0-jx
SOLIDWORKS Forums
9 dias atrás
Bearing fixture I am simulating a rotating shaft mounted by two pulleys when setting bearing fixtures as B.C, S.W always gives me wrong force connectors results
SOLIDWORKS Forums
10 dias atrás