I'm fairly new to SolidWorks Simulation Flow. I'm having trouble trying to put together a simulation flow through my heat sink using DC blower fans. I can't properly set up lids to do a boundary property with the inflow of the DC flowers and then properly set the out flow.
SOLIDWORKS Forums
13 hours ago
I am trying to read some of the white papers available on the SW website (Fluid Flow Simulation | White Papers | SOLIDWORKS
SOLIDWORKS Forums
5 days ago
I was doing an internal flow analysis when I encountered the "Mass flow is out of fan curve's range" warning message. My analysis involved an electronic enclosure with several electronic components and 3 internal fans. The warning is showing on 1 of the fan.
SOLIDWORKS Forums
5 days ago
Hi! Can someone help me, please .. I intend to do a 2D flow analysis of a wing with flaps assembly, but in defining the dimensions of the computational domain I've encountered a problem: the computational domain coordinate system does not correspond to the wing sketch coordinate system. So my question is how can I set the two coordinate systems so they fit?
SOLIDWORKS Forums
7 days ago
I am putting together an internal flow simulation problem for air flow entering some pipes at a particular volumatric flow rate and exiting to the normal atmosphere. I've done problems like this before and always set up the boundary conditions the same as I'm doing now, but for some reason it is not allowing me to do so and I am constantly getting "face "whatever"-lid is not laying laying on the boundary region between solid and fluid region. It's set up as internal flow, tried one side with
SOLIDWORKS Forums
10 days ago
One of my customer asked me that shall we do die cast flow simulation in solidworks..i was searched in net but i didnt find correct answer,can anyone tell me the suggestion Can SOLIDWORKS® Flow Simulation simulate the flow of molten aluminum?
SOLIDWORKS Forums
11 days ago
Cannot find corresponding .cpt file when loading .fld file I have setup and run a basic flow simulation on Solidworks 2017 on a Windows 10 machine.
SOLIDWORKS Forums
14 days ago
Greetings. I am trying to simulate the process of heating water on a stove, with the end goal being the heat flux through the sheet metal pan below the burner/flame. I already have empirical test results which capture pan temperature vs. time which I have been using to ground my simulations in reality. So far, they are not grounded.
SOLIDWORKS Forums
18 days ago
Flow simulation I am trying to simulate nozzle droplet distribution. I already made a nozzle but during flow simulation it showed that "the model is not watertight".
SOLIDWORKS Forums
18 days ago
Flow simulation through filter I'm trying to simulate the flow of CO2 gas through a metalic filter that is placed at the inlet of the vessel, but the results that i get doenst look reliable. I want to see how is the flow through the filter and the pressure drop at the outlet of the vessel.
SOLIDWORKS Forums
24 days ago
Total pressure loss results I'm modeling a showerhead in attempt to find total pressure loss. I have an inlet volumetric flow rate of 2 gpm and an outlet environmental pressure of 1 atm.
SOLIDWORKS Forums
28 days ago
Hello, I'm a student and I need to do the design of the image I posted. The thing is that I actually could made the gears, but how can I do an helical rack? Could someone send me their design, if you may? It's for an exposition and we don't work with Solidworks in our college, so I'm a little bit lost here and I have to send it at 18th of this month.
SOLIDWORKS Forums
1 month ago
Flow Simulation network solving ... I am having issues with adding a computer and need some assistance. I currently have a VM Server with 2013 SW with Flow Simulation installed and working properly.
SOLIDWORKS Forums
1 month ago
I am using Flow Simulation to model a thermoelectric cooler. I have a TEC with an aluminum plate on the "cold" side and an aluminum heat sink on the "hot" side. I got it to run steady state, but when I went back to add an 80W/°C thermal joint on each side of the TEC, I got nothing.
SOLIDWORKS Forums
1 month ago
Thermoelectric coolers Has anyone played with TEC in SW flow simulation?
SOLIDWORKS Forums
1 month ago
I am planning to create an air sealed enclosure( contains PCB and other electronic circuitry) for an application I am working on. How should the computational domain be modeled for CFD. Also I dont know if I should be using Electronics cooling module or thermal simulation to know the temperature inside as well as how to cool it. Much help appreciated
SOLIDWORKS Forums
1 month ago
Calculation continues after Solidworks crash I'm running a fairly large assembly simulation in flow. I had a couple of crashes when executing the simulation, not sure why.
SOLIDWORKS Forums
1 month ago
Flow Simulation Problem I'm running problem using flow simulation Solidworks 2018 Sp2 and Sp3, when i run the turbine with rotating region it does not behave to the i want but when i run without rotating region the behavior of the water is exactly what i want, I never had a problem like this in SW 2014 and 2015.
SOLIDWORKS Forums
1 month ago
Hi. Im starting to learn flow simulation trying to simulate known systems to me in order to be able to compare the sim result with my observation in real life. I have this case: it is a mixing chamber: it mixes air and pure O2. It takes air from the inlet, and there through a little tube pue O2 is inyected . a compressor takes this mix at the outlet.
SOLIDWORKS Forums
1 month ago
DRYING EXP: Hot Air insert to system 45 oC. Passing through black body and enters to drying chamber (White Body).
SOLIDWORKS Forums
1 month ago
I am creating an animation that shows a flow trajectory, then a particle injection starts halfway thru the video. My question is...why is the resolution so bad? Can someone tell me how to achieve a better looking animation?
SOLIDWORKS Forums
1 month ago
One of my students is making a simulation of 4-wheeled skate and the results are strange When i see the results of the velocity i see a complete red cutplot and the colorbar is changing
SOLIDWORKS Forums
1 month ago
Hello, I am new to CFD and I am trying to simulate the fluid flow for a fan in a blender. I have attached pictures of the models and the rotating region. I am not able go through the meshing for a finer mesh. For a coarser mesh (Global mesh level 3), its going through.
SOLIDWORKS Forums
1 month ago
So I was going to include a few fans in a flow simulation and the warning written in the title appeared. I tried to troubleshoot by only simulating a free fan in an empty domain, which still gave me the same warning. Now I need some help with how to resolve this.
SOLIDWORKS Forums
1 month ago