isometric section view center line issue Hi, I have created a drawing of an assembly with an isometric section view.
SOLIDWORKS Forums
14 hours ago
MBD- Hole table I'm using MBD and I have a large plate with many holes. Is it possible to do horizontal ordinate dimensions and if not, Is it possible to make a hole table with MBD?
SOLIDWORKS Forums
14 hours ago
I am saving a large solidworks assembly as STEP 203 files. I am using Large Assembly Mode, I have done a pack and go to save the assembly to my terminals hard drive instead of the network and have shut down every program except solidworks. The solidworks screen is now a light gray and giving me a message that 'solidworks 2017 is not responding'.
SOLIDWORKS Forums
14 hours ago
Hello, Anybody succeed in running SolidWorks on MacBook Pro 2017? I am considering to get the 13" version. Is the Intel Iris Plus Graphics 650 sufficiently good enough? Does Realview work?
SOLIDWORKS Forums
15 hours ago
I have a general question; What are the reasons when there is no convergence of displacement in a stress simulation.
SOLIDWORKS Forums
15 hours ago
Did anyone try the SW 2019 Beta version? I want to know what's new before i try it just in advance:
SOLIDWORKS Forums
16 hours ago
Glitchy geometry Has anyone else encountered this? How do I solve it?
SOLIDWORKS Forums
17 hours ago
Is the computer linked below a good computer for very large Solidworks assemblies? Want it to be better than current machine which runs the following on SW performance test:
SOLIDWORKS Forums
18 hours ago
I'm trying to create a rather large master template where configuration of components can be changed by just switching layers on and off. However this will use A LOT of layers, somewhere around the 200 - 300 mark so would really like to create a few folders for them. i.e outer, inner, parameters etc etc. Anyone have any idea on this?
SOLIDWORKS Forums
19 hours ago
I was successfully mapping current state to custom properties and tried to do same with "checked out by (Full name)" without any luck Jive Software Version: 2016.3.10.4, revision: 20180516024324.179277c.release_2016.3.10.4
SOLIDWORKS Forums
20 hours ago
I have an assembly (SW2018 sample attached) that uses five instances of the same riser block with each instance being a configuration. The only difference in each config is the length, which is why I'm using configs.
SOLIDWORKS Forums
21 hours ago
Hello SOLIDWORKS Power-Users and welcome to the 16th SWPUC. For 5,000 points and eternal glory proposed the best, most elegant technique for unknitting a surface body in its individual faces.
SOLIDWORKS Forums
21 hours ago
I will collect all winning solutions from the SWPUCs in this playlist: Let's see how many videos we can record before the end of the year.
SOLIDWORKS Forums
22 hours ago
I downloaded and installed 2018SP0.1. Running 2018 requires an upgrade to the License Manager.
SOLIDWORKS Forums
22 hours ago
From last week, anytime I start up Solidworks, it crashes after about 20 s regardless of any action you take. The error message I keep getting is Fault Module: ig9icd64:00021621
SOLIDWORKS Forums
22 hours ago
In my add-in I need to monitor if specific commands of third party add-ins are fired. If the commands are fired I need to run some code. What I am currently doing is to use CommandOpenPreNotify event to get the userCommand of the fired command.
SOLIDWORKS Forums
22 hours ago
For instance, if I am simulating heat loss of a liquid in a closed container, do I need to create a "solid" volume to fill the space between the liquid surface and the underside of the lid, or do I just leave it as a void? Should I also model a volume of air outside the container, or just apply free convection to the external surfaces? Related: if Iwantto define a volume as vacuum, do I leave it as a void, or fill the volume with a "solid" with 1e-15 (seems to be the lowest accepted value) for
SOLIDWORKS Forums
22 hours ago
I made the macro for creating the coverage in the multibody part. It's create the sketch, extrude it and apply the name(coverage) and material(veneer) to this new body.
SOLIDWORKS Forums
22 hours ago
Can someone tell me if this is possible? I've searched for hours trying to figure this out, and it would be really helpful with the particular product I'm working with right now. Anything helps!
SOLIDWORKS Forums
22 hours ago
I want to use the SVN functionality built into PCB for other files and programs. Has anyone setup TortoiseSVN to do this? I do not want to have separate servers/services running.
SOLIDWORKS Forums
22 hours ago
I have a glass bottle and a custom cap in which I'm trying to make matching threads. I have already done the threads on the bottle, so the problem that arises is the internal threads for the cap. I modeled the internal threads using the same thread measurements as I did with bottle threads. But when I take a cross section of the cap and bottle together, I see that the threads of the cap and bottle don't contact.
SOLIDWORKS Forums
23 hours ago
Using SW2013 SP0. I have created an exploded view of an assembly and placed the exploded view in a drawing. The view in the drawing is at a custom view and not a preset view (like ISO, etc.). The drawing has a BOM already inserted.
SOLIDWORKS Forums
23 hours ago
Hi have writen a macro that worked well on solidworks 2017 where it created custom property with linked global variable CustPropMgr.Add3 "Global Variable", swCustomInfoText, Chr(34) & "GlobalVariable@Default@part.SLDPRT" & Chr(34), swCustomPropertyReplaceValue
SOLIDWORKS Forums
23 hours ago
Details coming soon... Jive Software Version: 2016.3.10.4, revision: 20180516024324.179277c.release_2016.3.10.4
SOLIDWORKS Forums
23 hours ago