Co je nového v

Uživatelské fórum SOLIDWORKS

Místo, kde uživatelé SOLIDWORKS objevují, zapojují se a sdílejí vše, co se týká 3DEXPERIENCE Works –⁠ ať už využívají desktopovou verzi SOLIDWORKS, propojení s cloudem, nebo čistě cloudovou podobu.

Jednoduše se přihlaste pomocí 3DEXPERIENCE ID.

SOLIDWORKS User Forum
16 dnů před
Hello, My Design Library recently went blank. I didn't make any changes to the file paths since between it working and not working. But it is just blank now. Any help is appreciated. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Bonjour, Merci de m'aider pour résoudre le problème, avoir installé proprement solidworks electrical 2020 mais il me signale erreur database, voir photos ci-joint. Tous les autres applications dans solidworks fonctionnent parfaitement, sauf Electrical . Merci d'avance pour l'aide. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
I've been looking for a good model of a 75th percentile human being to sit next to a machine for scale. Does anybody have anything? No, it' doesn't have to be exactly 75%. I pulled that number out of thin air.
SOLIDWORKS User Forum
3 roků před
Everytime when I closed the Solidworks, this error will appear and I cannot close it by clicking the OK (It will show up again and again). I have to close it by opening the task manager and ending the task. This is quite annoying. Could anyone help me with that?
SOLIDWORKS User Forum
3 roků před
hello and gooday im having an issue with sizing my design table in the drawing as shown below in screen shots. ive resized the table in the part to reflect the proper size in the drawing, but no luck. ive tried adjusting design table scaling in drawing via right click table>properties>scaling, no luck. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Hey guys, I'm attempting to do some FEA analysis. After following some YouTube tutorials that recommended i active the option listed below in the first picture; I found that this option is not available. The first picture is the guide I was following and the second picture is what my screen looks like. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
And PDM. When I try to run I get following error. Can anyone help? SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
I was trying to switch my SolidWorks from a premium license I had to a student license I want to use. I uninstalled SolidWorks and deleted some remaining folders relating to SolidWorks. When I installed the student version I can't click "Install on this computer" since it is greyed out. Any help on how to fix this is appreciated. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Hello guys! Today, I was studying the forming tools and unintentionally deleted the forming toll from the "ribs" folder on my pc. As such, i would like to know if someone can send me the folders of the default formings tools or send only the forming tool in question. Regards, João Ferrão. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Hi, I have registered for the 3DEXPERIENCE World 2021 Certification Day. Does anyone know if it has a CSWE exam in the list? What exams will be in the list on the Certification Day? Thank you. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Connecting two parts on SW MBD I cannot connect these two part on the same Sketch. They are in different planes. How can I connect them so the fillet would look like this image? SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
On one of our computers, SolidWorks 2020 freezes instead of bringing up the dialog box when trying to delete a part. This happens on multiple drawings, but only happens with a certain Windows user profile. I've uninstalled and reinstalled, renamed folders in Appdata and AppdataRoaming. I've also done driver updates on the computer.
SOLIDWORKS User Forum
3 roků před
I made a sketch of a circle and used offset entities to make another curve...then used extrude boss/base, and the body looks super warped! Why is this happening? See attached pictures. Any input appreciated, Thanks! SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
How do I trim away the bottom of the circle sketch using the tangency points of the intersecting lines? I'm trying to do it with power trim however I can't select the intersection point in relation to the circle. It always thinks I'm selecting the line end point. SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
I'm experiencing a really bad memory leak with both SOLIDWORKS 2019 SP5.0, 2020 SP3.0, and 2020 SP5.0. Once the software starts up, it consumes an addtional 130MB of RAM per second, which gives me less than a minute before my computer bluescreens. Has anyone else experienced this issue, and is there any way of stopping it? SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
In this SolidWorks tutorial at 2:20, the guy giving the tutorial cycles through normal views very quickly. How does he do that? I know how to change view orientation, but I don't know whatever keyboard shortcut that is to "set your orientation." Any help appreciated Change View Orientations In SolidWorks - YouTube SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
every time when i try to flatten a cone it doesn't work... i make the sketch very simple to use edge flange so it is already a sheet metal part, but when i press the flatten feuture it collapses into an rectangle SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Hello When we need topology process? what should we do when maximum stress greater than yield ? Thank you SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Hello, I've installed SW2020 SP3 without big issues, but when I open SW the Wellcome window appears and I can select a file but when I want to open a file or create a part the system doesn't answer. Only the icon in the windows bar is in the screen. There is nothing in the screen, just the Windows' wallpaper. Please, anyone has the same problem? SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Using Remote Desktop and a Spacemouse. Has anybody had any luck with this in SW 2020? Thanks! SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
Hi, See the attached photo. I am trying to make a surface that is 90 degrees to this surface using the extruded surface command. I know I can use swept surface to create this, but isn't there a way to create this using extruded surface? Thanks! SolidworksGeneral
SOLIDWORKS User Forum
3 roků před
How to achieve assembly movement in DirveWorks Pro? The video below looks like this. At 4 minutes 45 seconds. 5 Reasons to Upgrade to DriveWorks Pro - YouTube 。
SOLIDWORKS User Forum
3 roků před