探索 SOLIDWORKS 使用者討論的內容。
I am designing a electrical contact spring. And also comparing it with actual result from testing Setup. From simulation i am getting Resultant force as 1.4 N and from actual testing of same Contact spring with measuring device i got the 0.8 N. Can anyone explain why is the difference so much ?
SOLIDWORKS Forums
2 小時 前
I'm trying to make some simulations of a rather simple part under static compression. The part is shown below. To make this simulation as simple as possible I have isolated the part (no assembly) and even removed features that would make things more complicated. I just want to see purely how much this part will deform under a given loading condition.
SOLIDWORKS Forums
6 小時 前
I'm fairly new to SolidWorks Simulation Flow. I'm having trouble trying to put together a simulation flow through my heat sink using DC blower fans. I can't properly set up lids to do a boundary property with the inflow of the DC flowers and then properly set the out flow.
SOLIDWORKS Forums
7 小時 前
I am trying to simulate the local flattening of a round aluminum pin (see image below). I'm doing a non-linear, static study. Model type;
SOLIDWORKS Forums
9 小時 前
I am trying to run a flow simulation in a strainer, to find out the pressure drop in the basket strainer. I have applied the boundary condition and trying to solve it but the pressure plot is giving me a strange result.
SOLIDWORKS Forums
10 小時 前
Update simulation parameters from external source My simulation model is just an step in a complex simulation workflow involving other software. Therefore, I need to run the simulation studies using model parameters (e.g. force values) generated in the previous step of the simulation workflow.
SOLIDWORKS Forums
23 小時 前
Connector forces calculation Applied only axial load of 3000 lbf on bolt connector. why connector forces show shear and bending too? How solidworks calculate shear and bending moment?
SOLIDWORKS Forums
2 天 前
Solidworks simulation returning incorrect natural frequencies. I'm testing out SolidWorks natural frequency FEA. I've made a simple cantilever beam out of Stainless Steel.
SOLIDWORKS Forums
2 天 前
I'm trying to do a structural analasis on a 3 d printed cast from a company called ActivArmor. The cast shape is very organic looking and because of that the STL file I was given is made up of thousands of triangles. I have left the simulation running for days and it cannot compute the mesh in that amount of time. Has anyone else been able to run simulations on complicated models made of thousands of faces?
SOLIDWORKS Forums
2 天 前
My names Chris, I am a beginner to SolidWorks simulation, my apologies if I use any incorrect terminology or assumptions. But can someone please help me with a current project I am working on.
SOLIDWORKS Forums
2 天 前
I am running SW2018 and I am trying to run a simple simulation. But I have a question about bolt connections. I have a simple assembly with a C profile bracket and a pipe that goes between the flanges and they have holes that are aligned to be bolted or to put a pin (refer screenshots).
SOLIDWORKS Forums
3 天 前
I want to simulate the suspension with rubber bearings like in the video The rubber is squeezed into the housing, so it is prestressed before any rotary motions.
SOLIDWORKS Forums
3 天 前
Past one week, I have been searching for sample test on CSWA - Simulation. Can someone please help in finding it. Atleast tell me if there are any sample test questions on CSWA - Simulation.
SOLIDWORKS Forums
3 天 前
I have a task where I must simulate two plates held together with a countersunk bolt under a shear load. I need to compare two scenarios, one where the bolt is properly tensioned/pre-loaded and another where it is not pre-loaded and will fail due to fatigue. To start I am using the SW connector bolts and I am able to run the static simulations fine.
SOLIDWORKS Forums
3 天 前
I have a research article that describes the simulation of a spring. I believe I am reproducing their model and study correctly but please have a look (paper attcahed). A negative Jacobian keeps occurring:
SOLIDWORKS Forums
3 天 前
Motion Study (Animation) Help Required EDIT: Thankyou for everyones contributions. I do not currently have the time to assess all the solutions offered, and mark one correct as I have to focus on other work now.
SOLIDWORKS Forums
4 天 前
When using an edgeweld connector if have to make a choice for "Material of weaker joined part" which defines the parts with the lowest tensile strength. BUt what do i have to do when both parts are made of the same material?
SOLIDWORKS Forums
4 天 前
can anyone suggest, what kind of study analysis to use for this problem in solidworks simulation. Cyclic loading problem. Please do not post questions from the actual exam here or anywhere else!
SOLIDWORKS Forums
4 天 前
I'm trying to model a balloon launch with temperature changes with time as it rises. The current simulation with the payload box entirely closed shows the battery getting too hot, so we definitely need a slotted hole for extra convection near the battery to better cool it down, but I don't know how to model that. I've tried adding a convection value along the sides of the slot or on top of the battery but that just gives unreal values, such as 20000°C battery.
SOLIDWORKS Forums
4 天 前
Using Solidworks 2017 - Solidworks Simulation add-on. I am conducting a random vibration (dynamic) study on an assembly and for some reason SW will not let me set my own maximum value for the stress plot. I.e.
SOLIDWORKS Forums
5 天 前
I am trying to read some of the white papers available on the SW website (Fluid Flow Simulation | White Papers | SOLIDWORKS
SOLIDWORKS Forums
5 天 前
I was doing an internal flow analysis when I encountered the "Mass flow is out of fan curve's range" warning message. My analysis involved an electronic enclosure with several electronic components and 3 internal fans. The warning is showing on 1 of the fan.
SOLIDWORKS Forums
5 天 前
Whenever I run simulations, I sometimes get problems with SolidWorks being able to find directories. Other errors I get are... "Failed to create temporary file.
SOLIDWORKS Forums
5 天 前
Are there any settings (in Solidworks or Windows) that speed up "show results" for simulations? I'd like to increase my efficiency. Thanks!
SOLIDWORKS Forums
6 天 前