探索 SOLIDWORKS 使用者討論的內容。
tried a few different method`s but none i can get to work closed i came with it is this
SOLIDWORKS Forums
12 小時 前
Hole Wizard using existing sketch I've seen comments along these lines - I just want to confirm
SOLIDWORKS Forums
12 小時 前
I will collect all winning solutions from the SWPUCs in this playlist: Let's see how many videos we can record before the end of the year.
SOLIDWORKS Forums
17 小時 前
Below is a custom material called 44W. The material has a material specific property called "GeneralName". That property has a value of "Steel". To be clear, all of these properties are within the Material.
SOLIDWORKS Forums
19 小時 前
I'm in the process of modeling some phone cases for the fun of it, and have come across a problem with the four corners of my case. As you can see, the interior walls are extruded to match the phones curved body, but I cannot figure out a good way to create the same feature going around the interior corners. I feel it is easier than it is made out to be, but thought I might post here for some tips and tricks on this problem, as well as for my overall design.
SOLIDWORKS Forums
1 天 前
A curve like solid is cut by using Surface Cut command. Boundary-Surface gives correct result whereas Surface-Loft gives an error message. What is the reason for that?
SOLIDWORKS Forums
3 天 前
In modeling a bowline knot by sweeping a spline, and choosing circular pattern to sweep on that spline, the end result looks good to the eye, but only until I zoom in on either one of the ends. Then do I find, not a circle but instead a circular-looking polygon of many segments. And the problem with this, is that I need one of those ends to mate concentrically in an assembly.
SOLIDWORKS Forums
3 天 前
I'm trying to trim (cut) the outer surface geometry of a part to match where it contacted a surface that was revolved 90 degrees around the parts axis. In the attached Part File, the part would be rotated around it's axis (yellow boss) 90 degrees and the outer surface of the part would be trimmed to match the contour of the red surface (similar to grinding the outer surface of the part with a cupped wheel while the part was rotated along it's axis 90 degrees). What is the best way to model this
SOLIDWORKS Forums
3 天 前
Wraping Flat Pattern I am new to the group and not sure if posting this in the correct location but here goes, we are using SW 2018 and was wondering if there Is any way to wrap the flat pattern around the contoured part? I just need it to wrap down the sides.
SOLIDWORKS Forums
3 天 前
I had a user attempt to use the Hole Wizard to put a M12 Shoulder screw counterbore into a part. Myself, I've never used the HW for this type of hole. But the user didn't find M12.
SOLIDWORKS Forums
3 天 前
I am puzzled why Draft5 will not circular pattern? Any ideas? hmm.. are CirPattern12 and CirPattern11 the same?
SOLIDWORKS Forums
3 天 前
I'm working on a macro that would make the process of saving parts as Step-files easier. But I have some issues and can't solve.
SOLIDWORKS Forums
4 天 前
Extrude surface along curve Hello!
SOLIDWORKS Forums
4 天 前
Help repairing corrupted files This morning when I tried to open two of my parts on SolidWorks, I got an error message saying that "an error was encountered while trying to open your file. Contact Technical Support for a possible solution."An error was encountered.PNGSolidWorks threw this error for only two of the part files (out of 14) that I have been working on recently.
SOLIDWORKS Forums
4 天 前
all section view colors in blue on solidwoks 2018 premium, what happened? Have you checked what your current appearances are?
SOLIDWORKS Forums
5 天 前
After the 2017 SP4 update i seem to be missing the dimensions within a sketch. I got View Sketch Dimensions turned on, aswell as the standard color scheme. Everything worked as normal before the latest service pack.
SOLIDWORKS Forums
5 天 前
If that title wasn't confusing enough for you, here is the more detailed version. I attached a picture of my part. I need this duplicated about 200 times unfortunately each part needs to be labeled A-1, A-2, A-3, B-1, B-2, B-3, and so on..
SOLIDWORKS Forums
5 天 前
I have a delete-face feature that fails when I do a ctrl-Q rebuild. One of the selected faces switches to a face in another solid body, which of course the delete-face feature cannot handle. The part starts with, among other things, a body with a cylindrical face. I spilt that body, then try to delete a reminant of the cyclindrical face in one solid body.
SOLIDWORKS Forums
5 天 前
Does anyone else experience frequent crashes when renaming a Display State? I've been irritated by this for a few releases now and was just wondering if it was only me experiencing this problem. It's happened to me a number of times.
SOLIDWORKS Forums
5 天 前
Is there a way to add center drills to a round part without having to draw them every time? I am kind of new to SW and haven't seen anything like that yet?
SOLIDWORKS Forums
6 天 前
Extruded Boss and end condition is 'up to the surface' is giving different result for solid body and surface body: -When body is solid extruded boss is perpendicular to sketch.
SOLIDWORKS Forums
6 天 前
Help with high resolution scanned file I am having trouble with my stl file which contains at least 800000 faces which I would like to run on solidworks cfd.
SOLIDWORKS Forums
6 天 前
I am (still) using SW2014 SP5. Some time in the past month or two toggling Tree Display / Show Flat Tree View does nothing. At first I assumed it was a file-specific issue but now I am pretty sure it is system wide.
SOLIDWORKS Forums
6 天 前
My computer crashed a few days ago. After that every part I open, SW will pop up a message to ask whether I want to open auto-saved version. Even if I opened the same parts again, it will still show up. How to fix it?
SOLIDWORKS Forums
6 天 前