Co je nového v

Uživatelské fórum SOLIDWORKS

Místo, kde uživatelé SOLIDWORKS objevují, zapojují se a sdílejí vše, co se týká 3DEXPERIENCE Works –⁠ ať už využívají desktopovou verzi SOLIDWORKS, propojení s cloudem, nebo čistě cloudovou podobu.

Jednoduše se přihlaste pomocí 3DEXPERIENCE ID.

this is assembly consist of two plates moving , when i click on motion study it not moving this message appeared i tried a lot but could not figure out , please need guidance Thank you very much SolidworksSimulation
SOLIDWORKS User Forum
3 roků před
hello This is a problem where roller do not rotate , and there is a hinge as a redundancey. Please guide how to remove this redundancey Thank you SolidworksSimulation
SOLIDWORKS User Forum
3 roků před
I am wondering what exactly base excitations are and how theyare applied and what the meaning of the results that come out ofSimulation in a dynamic analysis are?SolidworksSimulation
SOLIDWORKS User Forum
15 roků před
Got some problems while running a stress analysis. It`s justa small assembly, but it taking forever to run a simulation. Foundout that the folder with the assembly that used to be 3 mb, now was20 GB!?
SOLIDWORKS User Forum
14 roků před
como solucionar Solidworks simulation: "poisson's ratio should be less than 0.5"?, estoy tratando de hacer una simulacion de un ensamble con varios materiales, se crea la maya pero no me corre el estudio y muestra el mensaje de mas arriba. SolidworksSimulation
SOLIDWORKS User Forum
4 roků před
hi, srry someone know how bend this plane into sheet metal? here is the link it is for pie cut SolidworksSimulation
SOLIDWORKS User Forum
4 roků před
Beautiful. Vectors with a negative magnitude? That should make the design review entertaining. SolidworksSimulation
SOLIDWORKS User Forum
14 roků před
We are currently running drop test studies. 1 Analysis willtake at least 170 hours to complete. We had power failures in thenight longer than our UPS can handle. Is there any way that we can save or capture the run process sothat we can start the anlysis from there if the power fails again. SolidworksSimulation
SOLIDWORKS User Forum
15 roků před
Hi all, I have released the book on 2016 version of SolidWorks Simulation. I have tried to address common doubts in working with SolidWorks Simulation inside my book. I hope you will find the book helpful. The link is next. http://www.amazon.com/SolidWorks-Simulation-2016-Black-Book/dp/1523393742 SolidworksSimulation
SOLIDWORKS User Forum
8 roků před
Since installing SW2014, when I run a simulation, the Solving progress bar hits 100% after only a few minutes but if I expand the task pane the subtasks progress bar is still running through iterations and stiffness matrices. Anyone know if this is a bug or intended behaviour? Seems pointless to show incorrect overall progress. SolidworksSimulation
SOLIDWORKS User Forum
10 roků před
SOLIDWORKS User Forum
8 dnů před
Dear Gents, I Designed A Hydrolic Hot Press and everything was OK, while I tried to do Simulation either Static or Thermal I couldn't find any results, it stays for more than 10 Hours in meshing with no results at all. Please tell me if I miss something. Thanks, SolidworksSimulation
SOLIDWORKS User Forum
4 roků před
While running and FEA analysis on a chute I am receiving thefollowing error message: PCG iterative solver stopped status code 9: MATRIX_SINGULAR_OR_INDEFINITE may not have adequate restraints No results saved I have tried several restraint setups and all end up giving me thatsame error message. Does anyone know what this error message isfor? SolidworksSimulation
SOLIDWORKS User Forum
15 roků před
I created a custom library and added materials. All was finefor a while, when I added a material that had Orthotropicproperties, the database library would not open any more and showedan error window. Has anyone seen anything like this before? Thanks, Brian Wixom SolidworksSimulation
SOLIDWORKS User Forum
14 roků před
I have received an error stating "Unable to allocate memory" when running an FEA on an assembly. It has run for about an hour and a half, but then presents me with this error which causes the simulation to fail. How can I fix this? I have a 64-bit windows with 16GB of RAM and a processor running at 3.7 GHz. SolidworksSimulation
SOLIDWORKS User Forum
3 roků před
Hello guys, Could enyone help me... Could I make FME simulation in solidworks including intermittent weld? Or even better... Could I use weld from weldments (weld Bead)?
SOLIDWORKS User Forum
3 roků před
I got the following error message (simulation only went to 9%) before failing: The Iterative Solver stopped. Numerical difficulties. (Preconditioning failed) Please check model boundary conditions. No results saved. I'm trying to simulate how the weight affects the stand when a Christmas Tree is placed in the smaller (6 in in diameter) ring.
SOLIDWORKS User Forum
3 roků před
Alright I am driving myself crazy. Trying to ensure I am not going to break either wrench tooth off. I have constrained it but I don't necessarily know if I believe solidworks (potentially due to a constraint error?) I figured the teeth would show signs of displacement at least a small amount? I have attached my files SolidworksSimulation
SOLIDWORKS User Forum
4 roků před
I am working on a cryogenic system and am trying to set it up correctly to make sure that the resulting displacement from the input base excitation load. The load is applied through a user defined variation with time, harmonic time curve. Model is uploaded for review. SolidworksSimulation
SOLIDWORKS User Forum
3 roků před
When applying the motion study option, the program tells me that there is an error and closes. What can I do to solve it? SolidworksSimulation
SOLIDWORKS User Forum
3 roků před
I need to define the fixtures and loads for the model attached, it is one half of the pair of scissors. I am thinking of adding a hinge fixture to the axis and a load where the finger would go. I am not sure whatsoever -- how can I model the static analysis for this pair of scissors? All help is appreciated! SolidworksSimulation
SOLIDWORKS User Forum
4 roků před
Good morning, I´m new here and try to simulate a mixed model with shells and solid parts. In the shell manager are all sheets listet which are going to mesh as shell. Unfortunetly there is un error when I try to mesh the whole assembly: The thickness for one or more shells are not defined! How can I find the shell which is not correctly definded?
SOLIDWORKS User Forum
4 roků před
can i find out the worst orientation drop in drop testthanksSolidworksSimulation
SOLIDWORKS User Forum
14 roků před