### SOLIDWORKS 使用者論壇

SOLIDWORKS 使用者可於此探索、參與並分享 3DEXPERIENCE Works - SOLIDWORKS 桌面、雲端連線及雲端原生。

3DEXPERIENCE ID 登入即可。

How do you split an existing edge in #SOLIDWORKS? This is a critical skill for surface modeling when working with imported geometry. This is one way to do it: https://youtu.be/XpMUFwki6XY What is your technique? step Surfacing Surfaces loft boundary
6 月 前
Hi, I have a surface that I would like to thicken, however I need the thickness to be non uniform. Ideally i'm looking for a way of imposing a sort of grey scale map onto the surface and create a thickness using it. Is there a way to do this or another way that would achieve the same thing. The surface I need to thicken is a very organic shape to start with.
3 年 前
Hello, I am having a hard times modeling this case with a sharp line around the corners. I have been using the tool " boundary surface " with sketches in both directions. Let me know if that's something someone can help me with. Thanks in advance, Celia SolidworksSurfacing
3 年 前
Hi I'm not able to knit all surfaces together because of Boundary-Surface 53,54 and 55 and even the spoilers. Spoilers is overlapping the surface so that makes sense but I don't know whats wrong with 53,54 and 55. Everything else seems fine. Please help! SolidworksSurfacing
3 年 前
Hi How can I "extrude" the splitline in this model? (The split line feature is towards the end in feature manager bar) SolidworksSurfacing
3 年 前
I do the surface-loft them I do the cut with surface and it fails due to geometric condition. I did a similar model before and it worked so I dont know the reason its failing. Part2 worked fine Part3_3 did not work. SolidworksSurfacing
3 年 前
Hi all, I tried the like Measure, Section properties & Mass properties to find the surface area of the body. I couldn't able to get a one-click answer. So, later I calculated individually(or two surfaces) to find all areas of the surface. SolidworksSurfacing
4 年 前
Hello Gentlemen / Ladies question? has experience in surface modeling using POWER SURFACING overlays. Because I have some questions. Thank you in advance for your answer SolidworksSurfacing
4 年 前
Hi everyone, The surface body named Surface-Trim13 won't thicken to 2mm as needed - any suggestions would be great, thanks. File attached. SolidworksSurfacing
4 年 前
How to divide a sphere surface to 12 equal pentagonal ? SolidworksSurfacing
4 年 前
Hi! For my project I am attempting to design a plastic cover that could be injection molded. The issue I am having is adding a draft to the part. The neutral plane is at a weird angle - Using the drafting tool has not worked so far.
4 年 前
How to divide a sphere of equal parts? SolidworksSurfacing
4 年 前
Hello, I have this handle and I am trying to do an extruded cut, resulting in three cuts around the outside perimeter of it using this sketch. I should add they will only be a few millimeters deep and surround the entire handle. What method would I use to go about this? Thanks! SolidworksSurfacing
4 年 前
Hello, I am trying to make a simple, triangular, planar surface from the current sketch (Already done with the previous sketch). I know it's a closed sketch but the planar surface tool refuses to recognize the sketch as a feasible definition for it (aka the tool is unselectable/grayed out). Why is this happening? I attached the part file. SolidworksSurfacing
4 年 前
How to divide this surface area to 2 equal area like this ball model ? SolidworksSurfacing
4 年 前
Hi everyone! I'm Romain, new to this forum I would like to introduce you this SolidWorks tutorial I made. It aims at modeling an Aston Martin One-77. You can find it here : http://www.solidworks-aston-martin-one77.com/ This car tutorial is complete, available as PDF, you only need to know the basics of SolidWorks.
7 年 前
Just surfacing practice. SW2014 Files attached SolidworksSurfacing
8 年 前
I'm not quite sure what direction to go to complete this model the problem is this variable radius transitions that make the geometry diffucult to create. I'm close but need a little help. I may need to do some surfacing to finish it. Unfinished model attached along with dwg and jpegs of the cast part.
9 年 前
It has come to my attention that Mark has left SolidWorks. I advice we don't turn this into a guessing game of "why" but simply wish him the best in his future endeavours! It goes without saying that he will be missed in the SolidWorks community. Mark, maybe you'll swing by every now and then? SolidworksSurfacing
10 年 前
This is encouraging, it would be very handy to have an option for G2 with edge blends. Face blends to achieve this is just a hassle! http://www.tenlinks.com/news/PR/siemens_plm/100213_parasolid.htm SolidworksSurfacing
10 年 前
Hi, is somebody sees why extending Surface-Offset B is possible, when trying to do the same with Surface-Offset H is not ? Tx for your lighting. SolidworksSurfacing
11 年 前
SolidworksSurfacing
11 年 前
b SolidworksSurfacing
11 年 前
Bad News Bears. http://news.autodesk.com/news/autodesk/20111222005259/en/Autodesk-Acquires-T-Splines-Modeling-Technology-Assets I am very disappointed to hear this. We were set to purchase tsElements + T-Splines in January. Now I'm not seeing this as a good business move. SolidworksSurfacing
12 年 前