새로운 기능 알아보기:

SOLIDWORKS 사용자 포럼

SOLIDWORKS 사용자가 3DEXPERIENCE Works - SOLIDWORKS Desktop, 클라우드 연결 및 순수 클라우드에 대해 대해 발견하고 참여하고 공유하는 장입니다.

3DEXPERIENCE ID로 로그인하면 됩니다.

Is there a way to assign this leader setting to a part template? I've looked extensively but haven't found it yet. Thanks for any help. SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Hi Experts How can I make a model of a spring in 2 configurations. Normal and stretched state ? SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Anyone have a model for a Middle Atlantic model number - CFR-14-18 I already checked 3Dcontentcentral and GrabCAD SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Hi I'm looking through this part of a bicycle frame, which has the geometry laid out on a separate sketch. Each feature has a 'On Edge' relation to the geometry sketch. Does anyone know how it's created? These sketches don't seem to be derived from the geometry sketch.
SOLIDWORKS User Forum
3 년 전
Hi 1- I needed to create a macro where it is possible to rename the active configuration with the same file name, how can I do this? 2 - Possible when saving a document to run the macro together? SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Hi all, Quite often I work with mold files from customers. After saving off the assembly as a part file I want to remove all appearance properties (a lot of these molds come in with every part a different colour - really hard to work with). It sometimes takes over an hour for the command to run. Any idea why?
SOLIDWORKS User Forum
3 년 전
This keeps happening somewhat at random, but the part I am currently working on becomes grayed out after saving. It almost resembles a .step file but it was created entirely in Solidworks 2020. I can still edit the part, but for some reason the defined black lines disappear. I attached a normal part to show the difference.
SOLIDWORKS User Forum
3 년 전
Hello, I'm looking for a certain SolidWorks built in feature. What I'm looking is a way to link an assembly's name into its part's file properties. So basically something similar to $PRP:"SW-File Name(File Name)" , but for the assembly the part is contained into. I assume this is not possible so this is a shot in the dark.
SOLIDWORKS User Forum
3 년 전
Hello. I am trying to model the attached image using Solidworks. I tried modeling with a sweep, but the path looks complicated and I can't draw it. Is there a way to model it like an image file, or is there a way to model that isn't the same, but can look similar?
SOLIDWORKS User Forum
3 년 전
Thanks. SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
I just came across solution S-076397 in the knowledge base which includes a ZIP file of configurable weldment profiles for the ANSI, AS, BSI, CISC, DIN, GB, ISO and JIS standards. The configurable models are NOT available in the design library These are still the old unconfigurable versions. SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Hello, I can't seem to figure out how to partially select the grey sketch area inside the hash marks shown on the part in the attached photo and then how to get it to cut up and out to the exterior surface line following the arrows in the photo. Can someone help me out with this? SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Hi everyone, I hope you're all well and have been keeping safe. A quick question/issue I am having. I have set my part template file to be Z-Up, however, when selecting "normal to" for the front plane on the feature manager, it flips the view 180 degrees compared to the front view in the orientation window/view-cube. Any ideas on how to rectify this?
SOLIDWORKS User Forum
3 년 전
Hi, I want both edges to come together at the point and I'm unsure if the variable chamfer using hold line is the right method. I feel as though a loft wouldn't look clean and thought a cut would be easiest, but I am clearly open to suggestions. Thanks in advance SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Historically one of, in my opinion, the biggest disadvantages of CREO is the lack of Multibody support. Earlier this year with the introduction of CREO 7, PTC has knocked down this limitation and drawn one step closer to SW. SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
This is a very common CSWP preparation question. I watched the tutorial and followed it. I am supposed to receive 13206.34 but I receive 13171.41 g. I would be very happy to know my mistakes.
SOLIDWORKS User Forum
3 년 전
Hello, I am trying to print this nut 3D. The thread is custom (5/16-14 LH, modified). Can anyone please help with the THREAD START and THREAD TERMINATION so it can be printed properly. File is attached Thanks for your help.
SOLIDWORKS User Forum
3 년 전
Solidworks modeling - Tutorial 0055 ‌ SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Hello guys, attached is a file of my fuselage and the vertical stabilizer. When creating loft for the vertical stabilizer Solidworks is not recognizing it as one whole tangent surface. After creating the stabilizer with surface loft, there is a line dividing the tangent surface into two separate surfaces. I have no idea what I'm doing wrong.
SOLIDWORKS User Forum
3 년 전
I am attempting to create a chamfer as close to the first image as possible. I am attempting to utilize the partial edge parameters with the chamfer feature, but by utilizing this feature the chamfer no longer fades out. Is there a way to force the chamfer to fade out like it does before utilizing the partial edge parameter? SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Hello, as you guys can see on the screenshot, no matter whether I choose one or the other section/sketch as the first input, whenever I validate the function swept, it leads to the end section/ellipse not aligned to the planned sketch... How to fix it please? (The thing is that plane 47 is actually YZ plane, but plane 44 is XZ plane slightly rotated around X...) Regards SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
Can I / How to -- Loft or Boundary boss from a Curved Surface to a Plane Surface ??? IS IT POSSIBLE ?
SOLIDWORKS User Forum
3 년 전
When adding a cosmetic thread, the entire piece turns black SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전
I need to center an octagonal ring together with an internal spur gear and then join them together in a way that results in the octagonal ring being the outside of the gear. Could anyone give me advice on how to do this? ***EDIT Solved, using the solution in the comments*** Thanks! SolidworksParts And Features
SOLIDWORKS User Forum
3 년 전