The peace that i'm doing as this specifications: Can someone Help ? I need to optimize this ^solidworks help.jpg
SOLIDWORKS Forums
13 hours ago
I'm modelling a 4 bar linkage and am trying to optimize the design based on the angular displacement of the red link. This optimization is being done through the use of a design study, which uses motion analysis sensors as goals. When looking at the results from the motion study, sensible values for the link angular displacement are obtained.
SOLIDWORKS Forums
20 hours ago
PC-Specs: 6-core 6th generation interl i7 processor, 128gb ram with a samsung ssd. Solidworks 2017 I have been experiencing a very weird problem.
SOLIDWORKS Forums
23 hours ago
Thread simulation Hi, i have tried to make an accurate Nonlinear-Static thread (M12x1,75) simulation: the Torque-Load has always only max. 4% different to the analitical calculation,
SOLIDWORKS Forums
1 day ago
I am trying to design a pipe system with a pressure drop of less than 10 bar. The pump output pressure is 110bar, the output pressure is expected to be at least 100bar. However, when I try internal flow simulation and external flow simulation with the same boundary conditions applied, the results are totally different as shown below.
SOLIDWORKS Forums
1 day ago
I have simulation of parabolic dish solar collector, the simulation is completed but the results not loaded. the program appeared later content of it ( solidworks is out of memory! solidworks is now terminating). How solve this problem? Actually your memory was low, you should the capacity of ram.
SOLIDWORKS Forums
1 day ago
I'm getting familiar with SW Simulation solving some excersises from my mechanics of materials textbook. When it comes to shearing stresses, I'm getting results (close, but) different from zero on the outside corners of rectangular cross sections. In theory they should be zero. Am I getting these results due to a margin of error in the simulations or because some other reason?
SOLIDWORKS Forums
1 day ago
Is there a way to set parts in an assembly so that they will simulate contact while you try to move one of them? In Inventor, I would just take the parts and create a contact set. I'm not sure how to do the same thing in Solidworks.
SOLIDWORKS Forums
1 day ago
Metal (sheet) composite I'd like to compare deflections for a range of metal sheet thicknesses (say 0.3mm, 0.5mm, 0.8mm) that are bonded together to give a total thickness of around 5mm. The length and width of the sheets are 925mm x 470mm.
SOLIDWORKS Forums
1 day ago
Running Flow 2017. Does anybody know what happen to being able to plot the dynamic pressure on a surface plot? Only pressure seems available. Anyone?
SOLIDWORKS Forums
1 day ago
I have a pipe with a large diameter in 3D shape. Another pipe with smaller diameter but different material will need to be inserted in the large pipe to follow the 3D shape. Gravity effect will apply. need to find out the axial force ( friction force is known) and collision points to feed the smaller pipe into the large one. The larger pipe is solid and can't be deformed.
SOLIDWORKS Forums
1 day ago
helical gear contact line simulation I need to simulate the meshing of helical gears and see if a certain defect (chipping of one tooth for example) effects the contact line. i know that there's an option to look at the contact forces, but i'm more interested in looking at the contact itself. I'm adding a figure from an article which shows the contact line in color. i'd like to be able to produce the same thing only as an animation, and be able to change the tooth profile and see the influence.
SOLIDWORKS Forums
2 days ago
Thermal Study -Heat distribution between different layers- Incompatible initial temperatures I am running a Thermal Study in which i want to study the heat distribution from one body to another. Imagine a heating bed of 110C, over this bed i have solid body which will be divided into 3 layers.
SOLIDWORKS Forums
2 days ago
Has anyone ever seen results like this: Max Stress: 1.$, 0.0 stress in legend, Max: 0.00 displacement? Trying to get results for a random vibration input. Any suggestions as to what is wrong?
SOLIDWORKS Forums
2 days ago
I am new to using SolidWorks Flow Simulation. I am trying to run a simple laminar flow over a flat plate with constant heat flux analysis. I used SDC "An Introduction to SolidWorks Flow Simulation" (Chapter 2 Flat Plate Boundary Layer) as a guide however I tried to add a constant heat flux (q" = 5e+015 W/m^2) at a certain location (Image 2 between 10 and 10.01mm) but when I run my analysis the Temperature plot that is created does not seem correct(Image 1). I believe my issue lies in defining my
SOLIDWORKS Forums
2 days ago
porous media velocity results How does Flow Simulation calculate the average velocity on the surface of porous media? If I look at a contour or isoline plot of velocity on the surface, the result values make sense.
SOLIDWORKS Forums
2 days ago
minimum computer requirements I am running Solidworks Simulation 2017 and use large assemblies.
SOLIDWORKS Forums
2 days ago
Solver failed. Restart analysis? I'm running a linear static analysis for a contact problem.
SOLIDWORKS Forums
2 days ago
Every time I set up and run an analysis I find myself changing the plots from their defaults to something else, generally the same something else. For example, I always work in Mpa with no decimal places but the default in SW is N/m^2 in scientific notation. Surely there's a some setting somewhere that allows me to change these defaults to the ones I normally use?
SOLIDWORKS Forums
2 days ago
I have a piece of structure which is lifted with 4 slings. The structure has some internal load, but I have also put a small impact/side load on the structure. The analysis is failing always due to the error that the model is not stable, and have excessive displacements.
SOLIDWORKS Forums
2 days ago
I am running Linear static FEA in Solidworks simulation for an assembly in which all the parts are made up of steel. I usually consider only Von mises stresses as failure criterion for this assembly. But now i want to know the maximum tensile and compressive stress in the assembly and its location.
SOLIDWORKS Forums
2 days ago
There does not seem to be a way to plot applied force. Am I missing something? I know I can check reactions, but it would be great to display a color plot or XY plot of the parabolic distribution I (hopefully) set up.
SOLIDWORKS Forums
3 days ago
I have made numerous attempts to resolve this issue with SW 2016 SP4.0 flow simulation. Every time I attempt to run a simulation, I get this message : 'monitor lost connection with solver'.
SOLIDWORKS Forums
3 days ago
Solidwork Bolt Connector Problem I started to study solidwork bolt connector and its applications recently. However, there are some doubts that I could not figure out by finding answers online by myself.
SOLIDWORKS Forums
3 days ago