What does everyone think of NanoCAD vs Draftsight.? I have had enough of the activation issues with Draftsight and am seeking a new free alternative.
SOLIDWORKS Forums
5 dakika önce
i just receive email info thatSOLIDWORKS 2018 SP3 Early Visibility is ready, but in support page wont appear Are you subscribed to receive the EV versions??
SOLIDWORKS Forums
5 dakika önce
I've looked through the forum about using the scale feature/function to reduce or enlarge the size of a model. What I find amusing is that the icon itself for 'Scale' actually depicts an enlargement. Why do I find this amusing? Because it seems that on my SW2016 SP3 that's all I can do..... enlarge.
SOLIDWORKS Forums
23 dakika önce
Is it any macro available to rename a part and its references? I found this example, but its for Assembly only.
SOLIDWORKS Forums
34 dakika önce
Trim Surface Macro A macro to split a cylindrical surface with two planar surfaces, the end result is a quater of a cylinder. The trimmed surface is then mirrored about the plane.
SOLIDWORKS Forums
50 dakika önce
How many times do you see a great thread get trashed or hijacked for various reasons and I'll take the "Stand" and say I'm the worst for doing that.. So when I'm acting stupid tell me to trash it here, get it?? Rants - Cheers - Pet Peeves - or your Aunt Lilly, bring it.. (More then likely the dumbest thread anybody started, but I tried to keep it stupid, stupid) - The Forum Moderators rules still apply, no obscene pics, raunchy language and personal attacks, those will be reported and deleted if
SOLIDWORKS Forums
1 saat önce
No announcement, no notification of implemented, it just now works! Close SolidWorks with multiple file tabs open (saving when asked) and next time they are all there. No hunting around for files, or remembering where you were up to, just pick up where you left off.
SOLIDWORKS Forums
1 saat önce
A drawing was created in Solidworks 2012. Then it is re-saved in * .dwg format using the "Save As" command. But when you open a saved file in Bricscad, the drawing looks like this:
SOLIDWORKS Forums
2 saat önce
Am I the only person here that wishes the units could be changed in Vis to whatever I want (inches, feet, mm, cm etc)? The ability to enter units in a form I want would also be helpful. Like you can in SW.
SOLIDWORKS Forums
3 saat önce
I found this article and peaked my curiosity. What's your go-to music while you work?
SOLIDWORKS Forums
3 saat önce
I am creating a drawing of my part and i have all my settings to follow ISO-formatting. But when I try to Project a TOP view below my primary FRONT view it shows me the BOTTOM view as in ANSI-standard. How do I change this?
SOLIDWORKS Forums
3 saat önce
I have a few faulty lines which show up in a DXF and I don't know where they origin from. I think it's a bug but I haven't forwarded it to my VAR yet. Here's what I checked to try and find them:
SOLIDWORKS Forums
4 saat önce
Hole Wizard selecting near side countersink after creating countersunk hole Hi, When I use the hole wizard to create a countersunk hole it creates it as it should, but when I use the hole wizard again and select a different hole type, the 'Near side countersink' option is always ticked. It is really annoying and sometimes I forget that it has been ticked and add the extra feature, the countersink dimensions are equal to that of the last countersunk hole size I used.
SOLIDWORKS Forums
4 saat önce
Change annotation view I want to export Dimxpert dim. in drawing .As i show in pic . I want to show the diameter in front view1.png
SOLIDWORKS Forums
5 saat önce
scaling down knitted surface (solid) I cant seem to scale down the knitted surfaces even though i made them into a solid, does anyone know why?
SOLIDWORKS Forums
6 saat önce
Do you use the touch interface? If you do, 2 questions, what hardware (screen and stylus) and what type of design do you do? It seems touch is most accessible on small devices, but it's only really practical on large (expensive) devices. Do you actually use the interface (icons, menus) with touch, or just sketching, editing, graphical stuff?
SOLIDWORKS Forums
6 saat önce
Why the PDM asks if I would like to check out the file which is checked out by me? The only thing I can think of is that maybe you checked it out on a different computer. A check out is specific to a user and a computer.
SOLIDWORKS Forums
6 saat önce
I’m working on Solidworks 2014 and am trying to make a mate between a component and a coordinate system within an assembly. The manual way to do it is to select the origin on the component and the coordinate system and click mate, then ensure Align Axes is selected.
SOLIDWORKS Forums
7 saat önce
I am trying to figure out how to run a macro inside another macro. I want to set the flute type combobox to #0=none, #1=Straight Flute & #2=Spiral flute. If I select #(1)=Straight Flute, It runs the spiral delete macro.
SOLIDWORKS Forums
9 saat önce
Looking for the best way to create a rack & pinion from scratch SW 2018 Standard. Thanks Rick but I am running SolidWorks Standard which does not include the Tool Box. I want to design from scratch.
SOLIDWORKS Forums
9 saat önce
I did a project where I made a weldment frame, put it into an assembly and then made all the assembly & fabrication drawings, detailing each weldment member. I have a new project for a similar frame but with different dimensions & minor changes.
SOLIDWORKS Forums
10 saat önce
Is anyone have trouble with the variable radius not working in 2018? See below images. This is the preview window.
SOLIDWORKS Forums
10 saat önce
I don´t see any button that say "Helpful". Glenn SchroederMay 12, 2016 11:43 AM(in response to David Palacio Restrepo) That button was removed a while ago. Now there is only the Like button.
SOLIDWORKS Forums
11 saat önce
System Working super slow Hi, I Am using DELL Precision Tower 3620 Win10 with SW2014 and I have found the worst working experience with that. I am not sure either it is System or SW.
SOLIDWORKS Forums
11 saat önce