We use cookies to operate this website, improve its usability and track visits. Please note that by using this site you are consenting to the use of cookies.
Learn More |
Corner Relief I'm about to draw this part, and I don't know how to make the corner reliefs.
SOLIDWORKS Forums
1 day ago
I want install Solidworks 2014 64bit edu edition, but when I run hta file, error appear. I was follow solution from here :http://www.thewindowsclub.com/operation-has-been-cancelled-due-to-restrictions
SOLIDWORKS Forums
1 day ago
When I use the stretch command in 2017 and I choose remove items, the command changes to a move command. Tags:none(add)stretch remove items
SOLIDWORKS Forums
1 day ago
I have a student license for SolidWorks 2016. My current laptop cannot handle the demands of the software so I ordered a new laptop. My question is, can I transfer my existing license to the new laptop? If so, how do I go about it?
SOLIDWORKS Forums
1 day ago
A center of mass of the face is selected for this part. I wish to know whetherin this casecenter of mass of the part andcenter of faceis the same point. Make sure theView > Hide/Show > Center of Massoption is selected.
SOLIDWORKS Forums
1 day ago
Hello there, a quick question please. I am in the process of mating parts to a sketch in an assembly. This has worked up to a point then for some reason the sketch stops being 'selectable'.
SOLIDWORKS Forums
2 days ago
Surface Intersection Invalid Geometry Hello Helpful People!
SOLIDWORKS Forums
2 days ago
If you're going to need it just one time, then create a cut out in the area. Then add a flange will full face fillet. If you're simply modelling it yea, but if you send that out to the shop floor you may not be the favourite of the day though
SOLIDWORKS Forums
2 days ago
Last year, I downloaded Solidworks 2016-2017 Student Edition by filling solidworks.com/sek out with mine and the school's details. After doing so, an email was sent to my specified email address with the license code to be used in the installation manager - this all worked fine and Solidworks installed using this code. However, now that this license has expired after 365 days, I need to renew my license, as I graduate in July 2018 so still need access to Solidworks until then.
SOLIDWORKS Forums
2 days ago
I'm new to Solidworks. I tried to model the following object but I have to fillet all hard edges because in the real world we don't have any pure sharp edge. When I fillet sharp edges, SW hangs and when I click anywhere it crashes.
SOLIDWORKS Forums
2 days ago
I have assemblies consisting of a number of parts that need laser or plasma cutting. So a normally create a drawing on a custom sheet with the same size as my material. I then insert the flat pattern if each component on the same drawing. This work fine, but now I have assemblies with 100+ parts and it would be nice to generate a table of all the models used on one sheet.
SOLIDWORKS Forums
2 days ago
Somebody must have answered this question, but I can't find it: Is there a way toexcludesimulation results from a P&G in 2017? (I have SW Premium 2017 SP3.0 running under Windows 7 SP1.)
SOLIDWORKS Forums
2 days ago
I have this in assemble but one part isn't a "solid" and I really need to get the outline of this shape transferred to the other piece so I can laser cut it. Tell me what I'm doing wrong or a method on getting there. I have a good many more parts to make like this so figuring out how to get this done is important.
SOLIDWORKS Forums
2 days ago
Boundary Surface I am trying to use the Boundary Surface tool to create a solid surface from a few sketches I have. I keep getting the error: "Cannot create solid.
SOLIDWORKS Forums
2 days ago
My vote is Trek in Waterloo WI or maybe Fiskars in Madison WI I worked at a company in NC that developed aircraft seating and they slid that at 50+mph into walls. Impressive Truck crash.
SOLIDWORKS Forums
2 days ago
Hello, I am currently taking an Advanced Solidworks Class, I have installed the Engineering Kit for students year 2017. After I try opening solidworks I get an error that says"visual basic app error, are you low on disk space"and I have attached an screenshot to the forum. I have a alienware laptop so I know solidworks engineering kit will run well. I have windows 10 and visual basic app 7.1.
SOLIDWORKS Forums
2 days ago
Multiple Base Flanges I am creating a moment frame that requires stiffener plates, as shown in photo. I would normally create beams and column as a weldment and insert that into an assembly so I could then insert the stiffener plates as parts and mate them into place.
SOLIDWORKS Forums
2 days ago
Just started an assembly, and when I drop the customer parts in, the assembly file suddenly goes huge (i.e 180 MB - 500 MB bigger than the assembly should be. The customer parts are small molded pieces ( a few MB each) and likely originated in Catia. I am working in SW2017-4.1 ---- I have not used 2017 much, so not sure if this is a SW2017 issue, or just funky parts. In the customer part assemblies, I did notice some part faces that should be parallel actually .0001 - 004 degree off, but
SOLIDWORKS Forums
2 days ago
i have created the following assembly (is a CSWA sample; i'm training for the exam) but i 'm facing a problem as regards the mating of the shaft.Assembly.jpg All other parts are being mated but i can't find how to mate the shaftThe shaft is centered in the assembly horizontally (from left to
SOLIDWORKS Forums
2 days ago
In task scheduler, every time it completes a task it pops up solid works window. Is there any way, like it can completely be on background or no window pops up? Use "Run Minimized" option
SOLIDWORKS Forums
2 days ago
Screen size problem This is a screenshot of Solidworks Explorer. With my nose touching the screen, I can just about select the folders I want.
SOLIDWORKS Forums
3 days ago
Have a drawing macro I'm updating, part of the macro requires the model (asm or prt) to be opened, have a custom property changed, then saved. Now, i have seen it done a few different ways. I want to do it all silently so the user sees none of the steps.
SOLIDWORKS Forums
3 days ago
Please anybody hereto help me, fix toolbox problem in solidworks. Check and make sure that toolbox path is correctly mapped under Tools > Options > Hole Wizard/Toolbox
SOLIDWORKS Forums
3 days ago
I’ve just bought a dell xps13, and I been experiencing lag issues in solidworks (student edition 2016/2017) such as doing simple tasks such as opening a new part, sketching lines, selecting planes, etc I know my computer should be able to do those basic tasks since I have another laptop with the same specs, and it ran smoothed up to 30 parts. I tried reinstalling, modifying (going to programs, solidworks, modify, repair & update), tried solidworks 2016 and 2017), and factory resetting.
SOLIDWORKS Forums
3 days ago