探索 SOLIDWORKS 使用者討論的內容。
I have two static studies in a small assembly. They have different geometries. I created the first study and then a design study for it. Then I created the second (static) study and ran the design study, but I don't know which static study the design study solved for.
SOLIDWORKS Forums
11 分鐘 前
As I just set these two simpler components to describe my question. ↓This is the starting point of the motion.
SOLIDWORKS Forums
2 小時 前
When I simulated a basic design of two materials with a thin sheet of thermal insulating material in between them. There was no difference in temperature if I hadn't have put the TIM in it. Is this correctly modelling it or are there betters ways to introduce TIMs into a simulation?
SOLIDWORKS Forums
6 小時 前
dynamic motion analysis can anyone pls tell me how to conduct dynamic motion analysis in solidworks?
SOLIDWORKS Forums
9 小時 前
How to create/copy body from deformed shape from linear buckling/frequency analysis? The deformations seen in Buckling and Frequency are not true displacements. They are qualitative plots showing the mode of buckling failure or the mode of vibration at a certain frequency.
SOLIDWORKS Forums
21 小時 前
hello all animation guru's. I was wondering if users of Solidworks would be willing to post simple animation movies here of work they have done? Just for general interest.
SOLIDWORKS Forums
1 天 前
I am trying to run a mesh on a baja vehicle frame but every time I try to run it, it says the mesh has failed for 1 part. But every time I remove or suppress, it continues stating this message for another part. I'm afraid I can't help with Simulation, but I'm sure someone else will be able to.
SOLIDWORKS Forums
1 天 前
On microscopic levels surfaces aren't really flat. As far as I know CAD models are assumed to have perfect contact. I want to see the impact of a thermal insulating material on a display, the two different mediums being steel and aluminium.
SOLIDWORKS Forums
1 天 前
I have a recurring issue most frequently with connections (rigid, pin connector, etc.) where the green OK checkmark does nothing when pressed. The "keep visible" pushpin button is not pressed, so it is not trying to create multiple connections, it is simply not creating any at all. I cannot find any information on what might be causing this issue. Does anyone know why this occurs?
SOLIDWORKS Forums
1 天 前
I have to blocks settled on each other, and I would like to know the force that could push them off each other. If I add mates to make them on top of each other, the force would move both of them. How can I tell solidworks that they are different bodies but attached to each other, so I could find the force to separate them?
SOLIDWORKS Forums
1 天 前
I am currently working on a university assignment that involves doing a motion analysis on a Whitworth quick return mechanism that is used in a shaping machine, I have done mathematical analysis in order to obtain plots of the reciprocating rams displacement, velocity and acceleration, now I am looking to verify these results with a SolidWorks motion analysis study. I have created the simplified model pictured below and set up a motion analysis study in order to drive the system at a constant
SOLIDWORKS Forums
1 天 前
I can't understand how the design study receives such an angle? Instead of 30 degrees it shows 1900 degrees! How?!
SOLIDWORKS Forums
1 天 前
please see the att. error message box. I had the same message, I do not know what causes it. I found the simulation would run if using draft quality mesh but not the high quality mesh.
SOLIDWORKS Forums
1 天 前
I keep getting an error that reads, "Error in transferring special load". I'm not sure what this is or how to really solve it. I'm running a linear dynamic random vibration analysis using a base excitation of .01g^2/Hz on the downward plane of my box. The file is fairly large, so that may be getting in the way of it doing whatever it is trying to do.
SOLIDWORKS Forums
1 天 前
saludos cordiales, estoy diseñando un muro de contension tipo de gravedady quiero analizar mi estructura haciendo pazar una carga movil les agradesco de ante mano por cualquier sugerencia.
SOLIDWORKS Forums
2 天 前
I would like to know the correct way to set up boundary conditions for a hydraulic turbine, where the water entering the turbine is at approximately 23 PSI, and the pressure at the outlet is simply atmospheric pressure (14.7 PSI). The volume of water is also flowing through the turbine at a rate of 20 ft^3/s. Here's what I have tried so far:
SOLIDWORKS Forums
2 天 前
I would like to confirm that SolidWorks cannot correctly apply inertial relief to beam elements. When I try to apply inertial relief to a structure which is not fully restrained, I get fairly large displacements. Upon checking the .OUT file of the study, I can see that SW simulation knows there is a force imbalance, but it does not apply a counterbalance acceleration. I also noticed it is not registering any inertia mass in the model.
SOLIDWORKS Forums
2 天 前
Stress strain curve error - I'm working on a simulation for a plastic material with a stress-strain curve. I've defined the stress-strain curve in the solidworks material:
SOLIDWORKS Forums
2 天 前
I'm a japanese university student. I want to use roughness of boundary condition to research Aerodynamics of vehicle.
SOLIDWORKS Forums
3 天 前
I'd like to export the motion loads from a Motion Study into a static simulation of a sheet metal part. The part is only subjected to acceleration forces, following a rather complex shape, both rotation and translation. I'm able to export these motion loads to every other non-sheet metal part in my assembly, but not to the sheet metal part.
SOLIDWORKS Forums
3 天 前
Hi! I'm a beginner in the Solidworks world. I'm trying to simulate the strains suffered by the rectus femoris muscle. I already created the morphological model which contains the muscle itself and the two tendons.
SOLIDWORKS Forums
3 天 前
Hello, Is their any way to model and run thermal flow simulation on expandable graphite material? Is it possible through solid works flow simulation? I would really appreciate any help. Thank you
SOLIDWORKS Forums
3 天 前
Hello! I created a 8x4 prop model. When I run analisys for 2 blade prop, all is ok. But, if I change number of blades (cirpattern) - analisys doesn`t start and show following problem: "There is no fluid volume in the project.
SOLIDWORKS Forums
3 天 前
My question arises out of attempting to replace the glass bar, highlighted in the screen shot below, with a beam. The reason for this replacement, and for the whole modeling exercise, will become apparent (I hope) later, assuming you have the patience to read that far. First I must describe the assembly: The plates that support it against the restraints shown, and also the end pieces bonded onto the glass bar, are defined with very low density so that the COM of the assembly is essentially the
SOLIDWORKS Forums
4 天 前