We use cookies to operate this website, improve its usability and track visits. Please note that by using this site you are consenting to the use of cookies.
Learn More |
Discover what SOLIDWORKS users are discussing.
Project with surface function. Just as an FYI, check out zsurf: https://forum.solidworks.com/message/234998#234998
SOLIDWORKS Forums
3 days ago
Loft Problems I am a genuine novice with Solidworks - and I am having difficulty lofting 3 2d sketches to create a surface
SOLIDWORKS Forums
3 days ago
I am trying to model a quip toothbrush..I am not getting how to model the middle part which involves a delicate surface feature. I tried using sweep with guide curve but couldn't do it. I have attached both my model and the toothbrush image. Kindly help
SOLIDWORKS Forums
8 days ago
In this video Boundary Surface has been used to loft. I used Lofted Surface instead of Boundary Surface but the result is same. Is there any differences between using these two tools?
SOLIDWORKS Forums
14 days ago
Boundary-Surface Tool is used to create this feature. From the Selection Manager Box ‘Select Group’ is used to select curves to create the feature. ‘Select Group’ is not selecting curves in my sketch.
SOLIDWORKS Forums
15 days ago
I'm using Combine>Add to combine 3 Solid bodies into one. They are all touching each other with no interference (I'm going to troubleshoot that myself here after I get done posting). This is a model that was created in SW2006, that is now being adapted for a new purpose.
SOLIDWORKS Forums
15 days ago
Boundary-Surface Tool In the Boundary-Surface Tool “Tangency To Face option” was selected. When returned to edit mode again to see selected “Tangency To Face” option was back to “None” option again.
SOLIDWORKS Forums
16 days ago
What is the logical reason behind this? (or is it possible and I don't know?) In below illustration I can knit any 2 surfaces together.
SOLIDWORKS Forums
18 days ago
Hey i dont know whether this is possible but if not i figure it would make a awesome feature. I am building a model of a bracelet, idealy i would want to create it on a flat plane and then bend it along a curve? Is there anyway to do this in solidworks?
SOLIDWORKS Forums
19 days ago
Can't knit these surfaces I've been able to knit most of the surfaces. What's left is one of the small protrusions.
SOLIDWORKS Forums
21 days ago
I can't seem to figure out why the two surfaces can't be knit. I'm trying to knit the surfaces so that they can be thickened together Anyt tips/suggestions would be greatly appreciated!
SOLIDWORKS Forums
21 days ago
I am attempting to knit together the lofted surfaces that I have created with the faces of the extruded ribs (shown below) but I am encountering the message "the selected faces and surfaces cannot be knitted into one surface." After this, I intend to thicken the surface knit by 0.25mm. As an aside, I had asked this question earlier, but I did not get any responses, but what I am attempting to model is a wind turbine rib cage with a fabric wrapped around it and then aluminum around that.
SOLIDWORKS Forums
21 days ago
I can't get a tangent relation to work on this sketch (the corner spline in particular). The sketch is on a plane. It is using one sketch that was Convert Entities and then offset. I am not sure why this is happening but i have seen it before.
SOLIDWORKS Forums
22 days ago
What does this rebuild error/error message mean? What's the reason I can't create this loft?
SOLIDWORKS Forums
22 days ago
SW 2017 irregularly creates transfer on a surface... рукожопс... Bends a contour with shift and turn Безимени-1.jpg
SOLIDWORKS Forums
24 days ago
Issues thickening surface I am new to surfacing and am trying to learn by re-modeling an Xbox controller (see attached). I have a basic surface model down, but am running into issues when I try to thicken.
SOLIDWORKS Forums
25 days ago
I am quite new to Solidworks surfacing, and I am trying to thicken the surface in order to put it through Ansys. I have knitted all the separate components together but the tail seems to be the issue and I can't figure out why. It is a lofted surface with some surface fill and when I try to thicken it I get the following prompt: "Failed to offset or face could not be deleted".
SOLIDWORKS Forums
1 month ago
Trim Surface I want to trim this upper portion. Is it possible to use Trim Surface tool?
SOLIDWORKS Forums
1 month ago
Smoothing problem I'm trying to create a second surface between the 2 sketches, then 2 more flat surfaces and finally knit the whole to create a thin volume.
SOLIDWORKS Forums
1 month ago
I know that it's possible to create a solid from a surface, but was wondering if you can, & if so, what would be the best way to go about creating a surfaced feature, & then blending or converting that to a solid
SOLIDWORKS Forums
1 month ago
So I have researched this topic and can't seem to find the solution to my answer. I have created two surface lofts, trimmed the surfaces where they intersect, knitted the two surfaces together and then when I attempt to add a thickness it fails.
SOLIDWORKS Forums
1 month ago
Mirroring Option I want to mirror this rib to opposite site. Body and Feature both mirroring options are working.
SOLIDWORKS Forums
1 month ago
Question about Reverse Engineering Methods i am an undergraduate mechanical engineer student and on this semester i am working on my thesis. My work is to scan a part with a non contact 3d camera and then create a 3d model to evaluate its geometry.
SOLIDWORKS Forums
1 month ago
Sweep command is producing error result. How to fix it? In Feature Scope, uncheck the Auto-Select option & select the solid body you are trying merge the sweep with.
SOLIDWORKS Forums
1 month ago